AP License共享典型配置舉例

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

目  錄

1 簡介

2 配置前提

3 配置舉例

3.1 組網需求

3.2 配置注意事項

3.3 配置步驟

3.3.1 配置AC1

3.3.2 配置AC2

3.3.3 配置Switch

3.4 驗證配置

3.5 配置文件

4 相關資料

 

1  簡介

本文檔介紹了AP License共享典型配置舉例。

2  配置前提

本文檔不嚴格與具體軟、硬件版本對應，如果使用過程中與產品實際情況有差異，請以設備實際情況為準。

本文檔中的配置均是在實驗室環境下進行的配置和驗證，配置前設備的所有參數均采用出廠時的缺省配置。如果您已經對設備進行了配置，為了保證配置效果，請確認現有配置和以下舉例中的配置不衝突。

本文檔假設您已了解AP License共享特性。

3  配置舉例

3.1  組網需求

如圖1所示，AP通過交換機與AC1和AC2相連，AP為Client提供無線服務，配置SSID為service，在AC1和AC2上開啟AP License共享功能，兩台AC互為備份，當一台AC出現故障時，License也可以在備AC上繼續使用。

圖1 AP License共享組網圖

 

3.2  配置注意事項

當一台AC出現故障時，License可以在備AC上繼續使用的有效期為30天。

3.3  配置步驟

3.3.1  配置AC1

(1)     配置AC1的接口

# 創建VLAN 100及其對應的VLAN接口，並為該接口配置IP地址。AP將通過該IP地址與AC1建立CAPWAP隧道。

<AC1> system-view

[AC1] vlan 100

[AC1-vlan100] quit

[AC1] interface vlan-interface 100

[AC1-Vlan-interface100] ip address 112.12.1.25 16

[AC1-Vlan-interface100] quit

# 創建VLAN 200及其對應的VLAN接口，並為該接口配置IP地址。Client使用VLAN 200接入無線網絡。

[AC1] vlan 200

[AC1-vlan200] quit

[AC1] interface vlan-interface 200

[AC1-Vlan-interface200] ip address 112.13.1.25 16

[AC1-Vlan-interface200] quit

# 配置AC1和Switch相連的接口GigabitEthernet1/0/1為Trunk類型，禁止VLAN 1報文通過，允許VLAN 100和VLAN 200通過。

[AC1] interface gigabitethernet1/0/1

[AC1-GigabitEthernet1/0/1] port link-type trunk

[AC1-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[AC1-GigabitEthernet1/0/1] port trunk permit vlan 100 200

[AC1-GigabitEthernet1/0/1] quit

(2)     配置AP license共享功能，配置角色為主AC

[AC1] wlan ap-license-group

[AC1-wlan-ap-license-group] local ip 112.12.1.25

[AC1-wlan-ap-license-group] member ip 112.12.1.26

[AC1-wlan-ap-license-group] ap-license-synchronization enable

[AC1-wlan-ap-license-group] quit

(3)     配置無線服務

# 創建無線服務模板service，並配置SSID為service，配置Client從無線服務模板service上線後會被加入VLAN 200。

[AC1] wlan service-template service

[AC1-wlan-st-service] ssid service

[AC1-wlan-st-service] vlan 200

# 配置身份認證與密鑰管理模式為PSK模式，配置PSK密鑰為明文字符串12345678。

[AC1-wlan-st-service] akm mode psk

[AC1-wlan-st-service] preshared-key pass-phrase simple 12345678

# 配置加密套件為CCMP，安全信息元素為RSN。

[AC1-wlan-st-service] cipher-suite ccmp

[AC1-wlan-st-service] security-ie rsn

# 配置無線客戶端的數據報文轉發位置在AC上。（如果客戶端數據報文的缺省轉發位置與本配置相同，請跳過此步驟）

[AC1-wlan-st-service] client forwarding-location ac

# 使能無線服務模板。

[AC1-wlan-st-service] service-template enable

[AC1-wlan-st-service] quit

(4)     配置AP

 

# 創建AP，名稱為ap1，選擇AP型號並配置序列號。

[AC1] wlan ap ap1 model WA6320

[AC1-wlan-ap-ap1] serial-id 219801A28N819CE0002T

[AC1-wlan-ap-ap1] quit

# 創建AP組group1，並配置AP名稱入組規則。

[AC1] wlan ap-group group1

[AC-wlan-ap-group-group1] ap ap1

# 將無線服務模板service綁定到AP組group1下的Radio 1接口，並開啟射頻功能。

[AC1-wlan-ap-group-group1] ap-model WA6320

[AC1-wlan-ap-group-group1-ap-model-WA6320] radio 1

[AC1-wlan-ap-group-group1-ap-model-WA6320-radio-1] service-template service

[AC1-wlan-ap-group-group1-ap-model-WA6320-radio-1] radio enable

[AC1-wlan-ap-group-group1-ap-model-WA6320-radio-1] quit

[AC1-wlan-ap-group-group1-ap-model-WA6320] quit

[AC1-wlan-ap-group-group1] quit

3.3.2  配置AC2

(1)     配置AC2的接口

# 創建VLAN 100及其對應的VLAN接口，並為該接口配置IP地址。AP將通過該IP地址與AC2建立CAPWAP隧道。

<AC2> system-view

[AC2] vlan 100

[AC2-vlan100] quit

[AC2] interface vlan-interface 100

[AC2-Vlan-interface100] ip address 112.12.1.26 16

[AC2-Vlan-interface100] quit

# 創建VLAN 200及其對應的VLAN接口，並為該接口配置IP地址。Client使用VLAN 200接入無線網絡。

[AC2] vlan 200

[AC2-vlan200] quit

[AC2] interface vlan-interface 200

[AC2-Vlan-interface200] ip address 112.13.1.26 16

[AC2-Vlan-interface200] quit

# 配置AC2和Switch相連的接口GigabitEthernet1/0/1為Trunk類型，禁止VLAN 1報文通過，允許VLAN 100和VLAN 200通過。

[AC2] interface gigabitethernet1/0/1

[AC2-GigabitEthernet1/0/1] port link-type trunk

[AC2-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[AC2-GigabitEthernet1/0/1] port trunk permit vlan 100 200

[AC2-GigabitEthernet1/0/1] quit

(2)     配置AP license共享功能，配置角色為主AC

[AC2] wlan ap-license-group

[AC2-wlan-ap-license-group] local ip 112.12.1.26

[AC2-wlan-ap-license-group] member ip 112.12.1.25

[AC2-wlan-ap-license-group] ap-license-synchronization enable

[AC2-wlan-ap-license-group] quit

(3)     配置無線服務

# 創建無線服務模板service，並配置SSID為service，配置Client從無線服務模板service上線後會被加入VLAN 200。

[AC2] wlan service-template service

[AC2-wlan-st-service] ssid service

[AC2-wlan-st-service] vlan 200

# 配置身份認證與密鑰管理模式為PSK模式，配置PSK密鑰為明文字符串12345678。

[AC2-wlan-st-service] akm mode psk

[AC2-wlan-st-service] preshared-key pass-phrase simple 12345678

# 配置加密套件為CCMP，安全信息元素為RSN。

[AC2-wlan-st-service] cipher-suite ccmp

[AC2-wlan-st-service] security-ie rsn

# 配置無線客戶端的數據報文轉發位置在AC上。（如果客戶端數據報文的缺省轉發位置與本配置相同，請跳過此步驟）

[AC2-wlan-st-service] client forwarding-location ac

# 使能無線服務模板。

[AC2-wlan-st-service] service-template enable

[AC2-wlan-st-service] quit

(4)     配置AP

 

# 創建AP，名稱為ap1，選擇AP型號並配置序列號。

[AC2] wlan ap ap1 model WA6320

[AC2-wlan-ap-ap1] serial-id 219801A28N819CE0002T

[AC2-wlan-ap-ap1] quit

# 創建AP組group1，並配置AP名稱入組規則。

[AC2] wlan ap-group group1

[AC2-wlan-ap-group-group1] ap ap1

# 將無線服務模板service綁定到AP組group1下的Radio 1接口，並開啟射頻功能。

[AC2-wlan-ap-group-group1] ap-model WA6320

[AC2-wlan-ap-group-group1-ap-model-WA6320] radio 1

[AC2-wlan-ap-group-group1-ap-model-WA6320-radio-1] service-template service

[AC2-wlan-ap-group-group1-ap-model-WA6320-radio-1] radio enable

[AC2-wlan-ap-group-group1-ap-model-WA6320-radio-1] quit

[AC2-wlan-ap-group-group1-ap-model-WA6320] quit

[AC2-wlan-ap-group-group1] quit

3.3.3  配置Switch

# 創建VLAN 100和VLAN 200，其中VLAN 100用於轉發AC和AP間CAPWAP隧道內的流量，VLAN 200用於轉發Client無線報文。

<Switch> system-view

[Switch] vlan 100

[Switch-vlan100] quit

[Switch] vlan 200

[Switch-vlan200] quit

# 配置Switch與AC1相連的GigabitEthernet1/0/1接口的屬性為Trunk，禁止VLAN 1報文通過，允許VLAN 100和VLAN 200通過。

[Switch] interface gigabitethernet1/0/1

[Switch-GigabitEthernet1/0/1] port link-type trunk

[Switch-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[Switch-GigabitEthernet1/0/1] port trunk permit vlan 100 200

[Switch-GigabitEthernet1/0/1] quit

# 配置Switch與AC2相連的GigabitEthernet1/0/2接口的屬性為Trunk，禁止VLAN 1報文通過，允許VLAN 100和VLAN 200通過。

[Switch] interface gigabitethernet1/0/2

[Switch-GigabitEthernet1/0/2] port link-type trunk

[Switch-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[Switch-GigabitEthernet1/0/2] port trunk permit vlan 100 200

[Switch-GigabitEthernet1/0/2] quit

# 配置Switch與AP相連的接口屬性為Access，並允許VLAN 100通過，本例僅示例1個接口的配置。

[Switch] interface gigabitethernet1/0/3

[Switch-GigabitEthernet1/0/3] port link-type access

[Switch-GigabitEthernet1/0/3] port access vlan 100

# 開啟PoE接口遠程供電功能。

[Switch-GigabitEthernet1/0/3] poe enable

[Switch-GigabitEthernet1/0/3] quit

# 配置VLAN 100接口的IP地址。

[Switch] interface vlan-interface 100

[Switch-Vlan-interface100] ip address 112.12.1.27 16

[Switch-Vlan-interface100] quit

# 配置VLAN 200接口的IP地址。

[Switch] interface vlan-interface 200

[Switch-Vlan-interface200] ip address 112.13.1.27 16

[Switch-Vlan-interface200] quit

 # 開啟DHCP功能。

[Switch] dhcp enable

# 配置DHCP地址池100，用於為AP分配IP地址。

[Switch] dhcp server ip-pool 100

[Switch-dhcp-pool-100] network 112.12.0.0 mask 255.255.0.0

[Switch-dhcp-pool-100] gateway-list 112.12.1.27

[Switch-dhcp-pool-100] quit

# 配置DHCP地址池200，用於為Client分配IP地址。為Client分配的DNS服務器地址為網關地址（實際使用過程中請根據實際網絡規劃配置無線客戶端的DNS服務器地址）。

[Switch] dhcp server ip-pool 200

[Switch-dhcp-pool-200] network 112.13.0.0 mask 255.255.255.0

[Switch-dhcp-pool-200] gateway-list 112.13.1.27

[Switch-dhcp-pool-200] dns-list 112.13.1.27

[Switch-dhcp-pool-200] quit

3.4  驗證配置

(1)     在AC1可以查看AP license共享組已經建立。

<AC1> display wlan ap-license-group

Group total licenses: 32

Group used licenses: 2

AP license synchronization: Enabled

Local IP: 112.12.1.25

Local role: Master

Member information:

 IP address       Total     Used    Member role   State   Online duration

 112.12.1.26      16        0       Master        UP      10hr 22min 04sec

(2)     在AC2可以查看AP license共享組已經建立。

<AC2> display wlan ap-license-group

Group total licenses: 32

Group used licenses: 2

AP license synchronization: Enabled

Local IP: 112.12.1.26

Local role: Master

Member information:

 IP address       Total     Used    Member role   State   Online duration

 112.12.1.25      16        2       Master        UP      10hr 22min 04sec

(3)     當AC2出現故障後，AC1可以繼續使用組內的License，可以查看AP license共享組總license數仍然為32。

<AC1> display wlan ap-license-group

Group total licenses: 32

Group used licenses: 2

AP license synchronization: Enabled

Local IP: 112.12.1.25

Local role: Master

Member information:

 IP address       Total     Used    Member role   State   Online duration

 112.12.1.26      16        0       Master        DOWM    00hr 00min 00sec

3.5  配置文件

·     AC1：

#

vlan 100

#

vlan 200

#

wlan service-template service

 ssid service

 vlan 200

 client forwarding-location ac

 akm mode psk

 preshared-key pass-phrase cipher $c$3$QoCUXs4DmEXLHV9i25HKOnf4wdvj4i8EzJb+

 cipher-suite ccmp

 security-ie rsn

 service-template enable

#

interface Vlan-interface100

 ip address 112.12.1.25 255.255.0.0

#

interface Vlan-interface200

 ip address 112.13.1.25 255.255.0.0

#

interface GigabitEthernet1/0/1

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 200

#

wlan ap-group group1

 ap ap1

 ap-model WA6320

  radio 1

   radio enable

   service-template service

#

wlan ap ap1 model WA6320

 serial-id 219801A28N819CE0002T

#

wlan ap-license-group

 local ip 112.12.1.25

 member ip 112.12.1.26

 ap-license-synchronization enable

#

·     AC2：

#

vlan 100

#

vlan 200

#

wlan service-template service

 ssid service

 vlan 200

 client forwarding-location ac

 akm mode psk                                                                  

 preshared-key pass-phrase cipher $c$3$QoCUXs4DmEXLHV9i25HKOnf4wdvj4i8EzJb+    

 cipher-suite ccmp                                                              

 security-ie rsn

 service-template enable

#

interface Vlan-interface100

 ip address 112.12.1.26 255.255.0.0

#

interface Vlan-interface200

 ip address 112.13.1.26 255.255.0.0

#

interface GigabitEthernet1/0/1

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 200

#

wlan ap-group group1

 ap ap1

 ap-model WA6320

  radio 1

   radio enable

   service-template service

#

wlan ap ap1 model WA6320

 serial-id 219801A28N819CE0002T

#

wlan ap-license-group

 local ip 112.12.1.26

 member ip 112.12.1.25

 ap-license-synchronization enable

#

·     Switch：

#

 dhcp enable

#

vlan 100

#

vlan 200

#

dhcp server ip-pool vlan100

 gateway-list 112.12.1.27

 network 112.12.0.0 mask 255.255.0.0

#

dhcp server ip-pool vlan200

gateway-list 112.13.1.27

 network 112.13.0.0 mask 255.255.255.0

 dns-list 112.13.1.27

#

interface Vlan-interface100

 ip address 112.12.1.27 255.255.0.0

#

interface Vlan-interface200

 ip address 112.13.1.27 255.255.255.0

#

interface GigabitEthernet1/0/1

 port link-type trunk

undo port trunk permit vlan 1 

 port trunk permit vlan 100 200

#

interface GigabitEthernet1/0/2

 port link-type trunk

undo port trunk permit vlan 1 

 port trunk permit vlan 100 200

#

interface GigabitEthernet1/0/3

 port access vlan 100

 poe enable

#

4  相關資料

·     《H3C無線控製器產品 配置指導》中的“License管理配置指導”。

·     《H3C無線控製器產品 命令參考》中的“License管理命令參考”。