H3C S6890產品RRPP配置舉例

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

資料版本：6W100-20190628

 

Copyright © 2019 bobty下载软件 版權所有，保留一切權利。

非經本公司書麵許可，任何單位和個人不得擅自摘抄、複製本文檔內容的部分或全部，並不得以任何形式傳播。

除bobty下载软件 的商標外，本手冊中出現的其它公司的商標、產品標識及商品名稱，由各自權利人擁有。

本文檔中的信息可能變動，恕不另行通知。

目  錄

1 簡介

2 配置前提

3 使用限製

4 RRPP單環配置舉例

4.1 組網需求

4.2 配置思路

4.3 使用版本

4.4 配置注意事項

4.5 配置步驟

4.5.1 Device A的配置

4.5.2 Device B的配置

4.5.3 Device C的配置

4.5.4 Device D的配置

4.6 驗證配置

4.7 配置文件

5 RRPP單子環配置舉例

5.1 組網需求

5.2 配置思路

5.3 使用版本

5.4 配置注意事項

5.5 配置步驟

5.5.1 Device A的配置

5.5.2 Device B的配置

5.5.3 Device C的配置

5.5.4 Device D的配置

5.5.5 Device E的配置

5.5.6 Device F的配置

5.6 驗證配置

5.7 配置文件

6 RRPP雙歸屬環+相切環配置舉例

6.1 組網需求

6.2 配置思路

6.3 使用版本

6.4 配置注意事項

6.5 配置步驟

6.5.1 Device A的配置

6.5.2 Device B的配置

6.5.3 Device C的配置

6.5.4 Device D的配置

6.5.5 Device E的配置

6.5.6 Device F的配置

6.5.7 Device G的配置

6.5.8 Device H的配置

6.6 驗證配置

6.7 配置文件

7 相關資料

 

1  簡介

本文檔介紹了RRPP（Rapid Ring Protection Protocol，快速環網保護協議）的配置舉例。

2  配置前提

本文檔不嚴格與具體軟、硬件版本對應，如果使用過程中與產品實際情況有差異，請參考相關產品手冊，或以設備實際情況為準。

本文檔中的配置均是在實驗室環境下進行的配置和驗證，配置前設備的所有參數均采用出廠時的缺省配置。如果您已經對設備進行了配置，為了保證配置效果，請確認現有配置和以下舉例中的配置不衝突。

本文假設您已了解RRPP特性。

3  使用限製

·     請勿將接入RRPP環的端口的缺省VLAN配置為控製VLAN，而且控製VLAN內不能運行QinQ和VLAN映射功能，否則RRPP協議報文將無法正常收發。

·     配置主控製VLAN時，主控製VLAN和子控製VLAN的編號均不能與三層以太網子接口編號相同。

·     建議在RRPP端口上不要啟用OAM遠端環回功能，否則可能引起短時間的廣播風暴。

4  RRPP單環配置舉例

4.1  組網需求

如圖1所示，區域A和區域B的用戶接入一個環形的彙聚層網絡中，在該環網中使用VLAN 100～150承載語音業務、VLAN 151～200承載視頻業務。要求通過配置RRPP和以太網接口連接狀態抑製功能，實現如下需求：

·     二層網絡的環路預防和鏈路恢複功能。

·     語音和視頻流量走不同的拓撲，以實現鏈路的負載分擔。

·     設置RRPP環上所有以太網接口的物理連接狀態抑製時間為0秒，以提高RRPP的拓撲變化收斂速度。

圖1 RRPP單環配置組網圖

 

4.2  配置思路

·     為了實現語音和視頻流量走不同的拓撲，需要將整個環網劃分為兩個RRPP域：域1保護承載語音流量的VLAN 100～150，主節點為Device A；域2保護承載視頻流量的VLAN 151～200，主節點為Device B。

·     為了實現語音和視頻流量的鏈路的負載分擔，選擇Device A的Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口；Device B的Ten-GigabitEthernet1/0/2為主端口，Ten-GigabitEthernet1/0/1為副端口。這樣，語音流量和視頻流量的拓撲如圖2所示。

圖2 流量拓撲示意圖

 

4.3  使用版本

本舉例是在S6890-CMW710-R2712版本上進行配置和驗證的。

4.4  配置注意事項

·     配置好RRPP環之後不再允許用戶刪除或修改主控製VLAN。主控製VLAN隻能通過undo control-vlan命令刪除，不能通過undo vlan命令刪除。

·     在配置負載分擔時，不同RRPP域的保護VLAN必須不同。

·     配置RRPP端口角色時，必須關閉關於這些端口的生成樹協議，且這些端口不能是Smart Link組的成員端口。

·     缺省情況下，S6890係列交換機的接口處於ADM（Administratively Down）狀態，請根據實際需要在對應接口視圖下使用undo shutdown命令開啟接口。

4.5  配置步驟

4.5.1  Device A的配置

(1)     配置VLAN、MSTP實例和端口

# 創建VLAN 100～VLAN 200。

<DeviceA> system-view

[DeviceA] vlan 100 to 200

# 將VLAN 100～150映射到MSTI 1，VLAN 151～200映射到MSTI 2，並激活MST域的配置。

[DeviceA] stp region-configuration

[DeviceA-mst-region] instance 1 vlan 100 to 150

[DeviceA-mst-region] instance 2 vlan 151 to 200

[DeviceA-mst-region] active region-configuration

[DeviceA-mst-region] quit

# 將端口Ten-GigabitEthernet1/0/1和Ten-GigabitEthernet1/0/2配置為Trunk端口且允許VLAN 100～200通過，不允許VLAN 1通過，分別在端口上配置物理連接狀態up/down抑製時間為0秒（即不抑製），並關閉生成樹協議。

[DeviceA] interface ten-gigabitethernet 1/0/1

[DeviceA-Ten-GigabitEthernet1/0/1] port link-type trunk

[DeviceA-Ten-GigabitEthernet1/0/1] port trunk permit vlan 100 to 200

[DeviceA-Ten-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[DeviceA-Ten-GigabitEthernet1/0/1] link-delay 0 mode updown

[DeviceA-Ten-GigabitEthernet1/0/1] undo stp enable

[DeviceA-Ten-GigabitEthernet1/0/1] quit

[DeviceA] interface ten-gigabitethernet 1/0/2

[DeviceA-Ten-GigabitEthernet1/0/2] port link-type trunk

[DeviceA-Ten-GigabitEthernet1/0/2] port trunk permit vlan 100 to 200

[DeviceA-Ten-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[DeviceA-Ten-GigabitEthernet1/0/2] link-delay 0 mode updown

[DeviceA-Ten-GigabitEthernet1/0/2] undo stp enable

[DeviceA-Ten-GigabitEthernet1/0/2] quit

(2)     配置RRPP

# 創建RRPP域1。

[DeviceA] rrpp domain 1

# 配置域1的控製VLAN 1000，並將MSTI 1所映射的VLAN配置為該域的保護VLAN。

[DeviceA-rrpp-domain1] control-vlan 1000

[DeviceA-rrpp-domain1] protected-vlan reference-instance 1

# 配置Device A為主環主節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能主環。

[DeviceA-rrpp-domain1] ring 1 node-mode master primary-port ten-gigabitethernet 1/0/1 secondary-port Ten-GigabitEthernet 1/0/2 level 0

[DeviceA-rrpp-domain1] ring 1 enable

[DeviceA-rrpp-domain1] quit

# 創建RRPP域2。

[DeviceA] rrpp domain 2

# 配置域2的控製VLAN 2000，並將MSTI 2所映射的VLAN配置為該域的保護VLAN。

[DeviceA-rrpp-domain2] control-vlan 2000

[DeviceA-rrpp-domain2] protected-vlan reference-instance 2

# 配置Device A為主環傳輸節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能主環。

[DeviceA-rrpp-domain2] ring 1 node-mode transit primary-port ten-gigabitethernet 1/0/1 secondary-port Ten-GigabitEthernet 1/0/2 level 0

[DeviceA-rrpp-domain2] ring 1 enable

[DeviceA-rrpp-domain2] quit

# 全局使能RRPP。

[DeviceA] rrpp enable

4.5.2  Device B的配置

(1)     配置VLAN、MSTP實例和端口

# 創建VLAN 100～VLAN 200。

<DeviceB> system-view

[DeviceB] vlan 100 to 200

# VLAN 100～150映射到MST 1，VLAN 151～200映射到MST 2，並激活MST域的配置。

[DeviceB] stp region-configuration

[DeviceB-mst-region] instance 1 vlan 100 to 150

[DeviceB-mst-region] instance 2 vlan 151 to 200

[DeviceB-mst-region] active region-configuration

[DeviceB-mst-region] quit

# 將端口Ten-GigabitEthernet1/0/1和Ten-GigabitEthernet1/0/2配置為Trunk端口且允許VLAN 100～200通過，不允許VLAN 1通過，分別在端口上配置物理連接狀態up/down抑製時間為0秒（即不抑製），並關閉生成樹協議。

[DeviceB] interface ten-gigabitethernet 1/0/1

[DeviceB-Ten-GigabitEthernet1/0/1] port link-type trunk

[DeviceB-Ten-GigabitEthernet1/0/1] port trunk permit vlan 100 to 200

[DeviceB-Ten-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[DeviceB-Ten-GigabitEthernet1/0/1] link-delay 0 mode updown

[DeviceB-Ten-GigabitEthernet1/0/1] undo stp enable

[DeviceB-Ten-GigabitEthernet1/0/1] quit

[DeviceB] interface ten-gigabitethernet 1/0/2

[DeviceB-Ten-GigabitEthernet1/0/2] port link-type trunk

[DeviceB-Ten-GigabitEthernet1/0/2] port trunk permit vlan 100 to 200

[DeviceB-Ten-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[DeviceB-Ten-GigabitEthernet1/0/2] link-delay 0 mode updown

[DeviceB-Ten-GigabitEthernet1/0/2] undo stp enable

[DeviceB-Ten-GigabitEthernet1/0/2] quit

(2)     配置RRPP

# 創建RRPP域1。

[DeviceB] rrpp domain 1

# 配置域1的控製VLAN 1000，並將MSTI 1所映射的VLAN配置為該域的保護VLAN。

[DeviceB-rrpp-domain1] control-vlan 1000

[DeviceB-rrpp-domain1] protected-vlan reference-instance 1

# 配置Device B為主環傳輸節點，端口Ten-GigabitEthernet1/0/2為主端口，Ten-GigabitEthernet1/0/1為副端口，並使能主環。

[DeviceB-rrpp-domain1] ring 1 node-mode transit primary-port ten-gigabitethernet 1/0/2 secondary-port ten-gigabitethernet 1/0/1 level 0

[DeviceB-rrpp-domain1] ring 1 enable

[DeviceB-rrpp-domain1] quit

# 創建RRPP域2。

[DeviceB] rrpp domain 2

# 配置域2的控製VLAN 2000，並將MSTI 2所映射的VLAN配置為該域的保護VLAN。

[DeviceB-rrpp-domain2] control-vlan 2000

[DeviceB-rrpp-domain2] protected-vlan reference-instance 2

# 配置Device B為主環主節點，端口Ten-GigabitEthernet1/0/2為主端口，Ten-GigabitEthernet1/0/1為副端口，並使能主環。

[DeviceB-rrpp-domain2] ring 1 node-mode master primary-port ten-gigabitethernet 1/0/2 secondary-port ten-gigabitethernet 1/0/1 level 0

[DeviceB-rrpp-domain2] ring 1 enable

[DeviceB-rrpp-domain2] quit

# 全局使能RRPP。

[DeviceB] rrpp enable

4.5.3  Device C的配置

(1)     配置VLAN、MSTP實例和端口

# 創建VLAN 100～VLAN 200。

<DeviceC> system-view

[DeviceC] vlan 100 to 200

# VLAN 100～150映射到MSTI 1，VLAN 151～200映射到MSTI 2，並激活MST域的配置。

[DeviceC] stp region-configuration

[DeviceC-mst-region] instance 1 vlan 100 to 150

[DeviceC-mst-region] instance 2 vlan 151 to 200

[DeviceC-mst-region] active region-configuration

[DeviceC-mst-region] quit

# 將端口Ten-GigabitEthernet1/0/1和Ten-GigabitEthernet1/0/2配置為Trunk端口且允許VLAN 100～200通過，不允許VLAN 1通過，分別在端口上配置物理連接狀態up/down抑製時間為0秒（即不抑製），並關閉生成樹協議。

[DeviceC] interface ten-gigabitethernet 1/0/1

[DeviceC-Ten-GigabitEthernet1/0/1] port link-type trunk

[DeviceC-Ten-GigabitEthernet1/0/1] port trunk permit vlan 100 to 200

[DeviceC-Ten-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[DeviceC-Ten-GigabitEthernet1/0/1] link-delay 0 mode updown

[DeviceC-Ten-GigabitEthernet1/0/1] undo stp enable

[DeviceC-Ten-GigabitEthernet1/0/1] quit

[DeviceC] interface ten-gigabitethernet 1/0/2

[DeviceC-Ten-GigabitEthernet1/0/2] port link-type trunk

[DeviceC-Ten-GigabitEthernet1/0/2] port trunk permit vlan 100 to 200

[DeviceC-Ten-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[DeviceC-Ten-GigabitEthernet1/0/2] link-delay 0 mode updown

[DeviceC-Ten-GigabitEthernet1/0/2] undo stp enable

[DeviceC-Ten-GigabitEthernet1/0/2] quit

(2)     配置RRPP

# 創建RRPP域1。

[DeviceC] rrpp domain 1

# 配置域1的控製VLAN 1000，並將MSTI 1所映射的VLAN配置為該域的保護VLAN。

[DeviceC-rrpp-domain1] control-vlan 1000

[DeviceC-rrpp-domain1] protected-vlan reference-instance 1

# 配置Device C為主環傳輸節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能主環。

[DeviceC-rrpp-domain1] ring 1 node-mode transit primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 0

[DeviceC-rrpp-domain1] ring 1 enable

[DeviceC-rrpp-domain1] quit

# 創建RRPP域2。

[DeviceC] rrpp domain 2

# 配置域2的控製VLAN 2000，並將MSTI 2所映射的VLAN配置為該域的保護VLAN。

[DeviceC-rrpp-domain2] control-vlan 2000

[DeviceC-rrpp-domain2] protected-vlan reference-instance 2

# 配置Device C為主環傳輸節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能主環。

[DeviceC-rrpp-domain2] ring 1 node-mode transit primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 0

[DeviceC-rrpp-domain2] ring 1 enable

[DeviceC-rrpp-domain2] quit

# 全局使能RRPP。

[DeviceC] rrpp enable

4.5.4  Device D的配置

(1)     配置VLAN、MSTP實例和端口

# 創建VLAN 100～VLAN 200。

<DeviceD>system-view

[DeviceD] vlan 100 to 200

# VLAN 100～150映射到MSTI 1，VLAN 151～200映射到MSTI 2，並激活MST域的配置。

[DeviceD] stp region-configuration

[DeviceD-mst-region] instance 1 vlan 100 to 150

[DeviceD-mst-region] instance 2 vlan 151 to 200

[DeviceD-mst-region] active region-configuration

[DeviceD-mst-region] quit

# 將端口Ten-GigabitEthernet1/0/1和Ten-GigabitEthernet1/0/2配置為Trunk端口且允許VLAN 100～200通過，不允許VLAN 1通過，分別在端口上配置物理連接狀態up/down抑製時間為0秒（即不抑製），並關閉生成樹協議。

[DeviceD] interface ten-gigabitethernet 1/0/1

[DeviceD-Ten-GigabitEthernet1/0/1] port link-type trunk

[DeviceD-Ten-GigabitEthernet1/0/1] port trunk permit vlan 100 to 200

[DeviceD-Ten-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[DeviceD-Ten-GigabitEthernet1/0/1] link-delay 0 mode updown

[DeviceD-Ten-GigabitEthernet1/0/1] undo stp enable

[DeviceD-Ten-GigabitEthernet1/0/1] quit

[DeviceD] interface ten-gigabitethernet 1/0/2

[DeviceD-Ten-GigabitEthernet1/0/2] port link-type trunk

[DeviceD-Ten-GigabitEthernet1/0/2] port trunk permit vlan 100 to 200

[DeviceD-Ten-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[DeviceD-Ten-GigabitEthernet1/0/2] link-delay 0 mode updown

[DeviceD-Ten-GigabitEthernet1/0/2] undo stp enable

[DeviceD-Ten-GigabitEthernet1/0/2] quit

(2)     配置RRPP

# 創建RRPP域1。

[DeviceD] rrpp domain 1

# 配置域1的控製VLAN 1000，並將MSTI 1所映射的VLAN配置為該域的保護VLAN。

[DeviceD-rrpp-domain1] control-vlan 1000

[DeviceD-rrpp-domain1] protected-vlan reference-instance 1

# 配置Device D為主環傳輸節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能主環。

[DeviceD-rrpp-domain1] ring 1 node-mode transit primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 0

[DeviceD-rrpp-domain1] ring 1 enable

[DeviceD-rrpp-domain1] quit

# 創建RRPP域2。

[DeviceD] rrpp domain 2

# 配置域2的控製VLAN 2000，並將MSTI 2所映射的VLAN配置為該域的保護VLAN。

[DeviceD-rrpp-domain2] control-vlan 2000

[DeviceD-rrpp-domain2] protected-vlan reference-instance 2

# 配置Device D為主環傳輸節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能主環。

[DeviceD-rrpp-domain2] ring 1 node-mode transit primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 0

[DeviceD-rrpp-domain2] ring 1 enable

[DeviceD-rrpp-domain2] quit

# 全局使能RRPP。

[DeviceD] rrpp enable

4.6  驗證配置

# 查看Device A的RRPP域1詳細信息。

[DeviceA] display rrpp verbose domain 1

 Domain ID     : 1

Control VLAN  : Primary 1000, Secondary 1001

Protected VLAN: Reference instance 1

Hello timer   : 1 seconds, Fail timer: 3 seconds

Fast detection status: Disabled

Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Master

Ring State    : Completed

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                    Port status: UP

Secondary port: XGE1/0/2                    Port status: BLOCKED

顯示信息表示Device A在RRPP域1中為主節點，且RRPP域1中主環狀態為completed，主端口up，副端口blocked。

# 查看Device A的RRPP域2詳細信息，。

[DeviceA] display rrpp verbose domain 2

Domain ID     : 2

Control VLAN  : Primary 2000, Secondary 2001

Protected VLAN: Reference instance 2

Hello timer   : 1 seconds, Fail timer: 3 seconds

Fast detection status: Disabled

Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                    Port status: UP

Secondary port: XGE1/0/2                    Port status: UP

顯示信息表示Device A在RRPP域2中為傳輸節點，RRPP端口狀態均為up。

# 查看Device B的RRPP域1詳細信息。

[DeviceB] display rrpp verbose domain 1

 Domain ID     : 1

Control VLAN  : Primary 1000, Secondary 1001

Protected VLAN: Reference instance 1

Hello timer   : 1 seconds, Fail timer: 3 seconds

Fast detection status: Disabled

Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/2                    Port status: UP

Secondary port: XGE1/0/1                    Port status: UP

顯示信息表示Device B在RRPP域1中為傳輸節點，RRPP端口狀態均為up。

# 查看Device B的RRPP域2詳細信息。

[DeviceB] display rrpp verbose domain 2

 Domain ID     : 2

Control VLAN  : Primary 2000, Secondary 2001

Protected VLAN: Reference instance 2

Hello timer   : 1 seconds, Fail timer: 3 seconds

Fast detection status: Disabled

Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Master

Ring State    : Completed

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/2                    Port status: UP

Secondary port: XGE1/0/1                    Port status: BLOCKED

顯示信息表示Device B在RRPP域2中為主節點，且RRPP域2中主環狀態為completed，主端口up，副端口blocked。

# 查看Device C的RRPP域1詳細信息。

[DeviceC] display rrpp verbose domain 1

 Domain ID     : 1

Control VLAN  : Primary 1000, Secondary 1001

Protected VLAN: Reference instance 1

Hello timer   : 1 seconds, Fail timer: 3 seconds

Fast detection status: Disabled

Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                    Port status: UP

Secondary port: XGE1/0/2                    Port status: UP

顯示信息表示Device C在RRPP域1中為傳輸節點，RRPP端口狀態均為up。

# 查看Device C的RRPP域2詳細信息。

[DeviceC] display rrpp verbose domain 2

 Domain ID     : 2

Control VLAN  : Primary 2000, Secondary 2001

Protected VLAN: Reference instance 2

Hello timer   : 1 seconds, Fail timer: 3 seconds

Fast detection status: Disabled

Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                    Port status: UP

Secondary port: XGE1/0/2                    Port status: UP

顯示信息表示Device C在RRPP域2中為傳輸節點，RRPP端口狀態均為up。

Device D的查看結果與Device C一致，不再贅述。

4.7  配置文件

·     Device A：

#

 sysname DeviceA

#

vlan 1

#

vlan 100 to 200

#

stp region-configuration

 instance 1 vlan 100 to 150

 instance 2 vlan 151 to 200

 active region-configuration

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

rrpp domain 1

 control-vlan 1000

 protected-vlan reference-instance 1

 ring 1 node-mode master primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 0

 ring 1 enable

#

rrpp domain 2

 control-vlan 2000

 protected-vlan reference-instance 2

 ring 1 node-mode transit primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 0

 ring 1 enable

#

rrpp enable

#

·     Device B：

#

 sysname DeviceB

#

vlan 1

#

vlan 100 to 200

#

stp region-configuration

 instance 1 vlan 100 to 150

 instance 2 vlan 151 to 200

 active region-configuration

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

rrpp domain 1

 control-vlan 1000

 protected-vlan reference-instance 1

 ring 1 node-mode transit primary-port Ten-GigabitEthernet1/0/2 secondary-port Ten-GigabitEthernet1/0/1 level 0

 ring 1 enable

#

rrpp domain 2

 control-vlan 2000

 protected-vlan reference-instance 2

 ring 1 node-mode master primary-port Ten-GigabitEthernet1/0/2 secondary-port Ten-GigabitEthernet1/0/1 level 0

 ring 1 enable

#

rrpp enable

#

·     Device C：

#

 sysname DeviceC

#

vlan 1

#

vlan 100 to 200

#

stp region-configuration

 instance 1 vlan 100 to 150

 instance 2 vlan 151 to 200

 active region-configuration

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

rrpp domain 1

 control-vlan 1000

 protected-vlan reference-instance 1

 ring 1 node-mode transit primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 0

 ring 1 enable

#

rrpp domain 2

 control-vlan 2000

 protected-vlan reference-instance 2

 ring 1 node-mode transit primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 0

 ring 1 enable

#

rrpp enable

#

·     Device D：

#

 sysname DeviceD

#

vlan 1

#

vlan 100 to 200

#

stp region-configuration

 instance 1 vlan 100 to 150

 instance 2 vlan 151 to 200

 active region-configuration

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

rrpp domain 1

 control-vlan 1000

 protected-vlan reference-instance 1

 ring 1 node-mode transit primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 0

 ring 1 enable

#

rrpp domain 2

 control-vlan 2000

 protected-vlan reference-instance 2

 ring 1 node-mode transit primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 0

 ring 1 enable

#

rrpp enable

#

5  RRPP單子環配置舉例

5.1  組網需求

如圖3所示，某接入層以環網形式接入彙聚層，彙聚層網絡也是一個環網。該網絡中使用VLAN 100～150承載語音業務、VLAN 151～200承載視頻業務。要求通過配置RRPP和以太網接口連接狀態抑製功能，實現如下需求：

·     二層網絡的環路預防和鏈路恢複功能。

·     使語音和視頻流量走不同的拓撲，以實現鏈路的負載分擔。

·     設置所有環上以太網端口的物理連接狀態抑製時間為0秒，以提高RRPP的拓撲變化收斂速度。

圖3 RRPP單子環配置組網圖

 

5.2  配置思路

·     RRPP主環需要透傳子環的保護VLAN和控製VLAN內的流量，需要有較強的數據傳輸能力。本例中選擇彙聚層環網作為主環（Ring 1），接入層環網作為子環（Ring 2）。

·     為了實現語音和視頻流量走不同的拓撲，需要將整個環網劃分為兩個RRPP域：域1保護承載語音流量的VLAN 100～150，Ring 1主節點為Device A，Ring 2主節點為Device E；域2保護承載視頻流量的VLAN 151～200，Ring 1主節點為Device B，Ring 2主節點為Device F。

·     為了實現語音和視頻流量的鏈路的負載分擔，選擇Device A的Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口；Device B的Ten-GigabitEthernet1/0/2為主端口，Ten-GigabitEthernet1/0/1為副端口；Device E的Ten-GigabitEthernet1/0/2為主端口，Ten-GigabitEthernet1/0/1為副端口；Device F的Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口。這樣，語音流量和視頻流量的拓撲如圖4所示。

圖4 流量拓撲示意圖

 

5.3  使用版本

本舉例是在S6890-CMW710-R2712版本上進行配置和驗證的。

5.4  配置注意事項

·     配置邊緣節點和輔助邊緣節點時，必須先配置主環再配置子環。

·     配置好RRPP環之後不再允許用戶刪除或修改控製主VLAN。主控製VLAN隻能通過undo control-vlan命令刪除，不能通過undo vlan命令刪除。

·     在配置負載分擔時，不同RRPP域的保護VLAN必須不同。

·     在一台設備上使能子環之前必須先使能主環，而關閉主環之前也必須先關閉所有子環，否則係統將提示出錯。

·     如果一台設備處於同一RRPP域的多個RRPP環上，則該設備在子環上的節點角色隻能是邊緣節點或輔助邊緣節點。

·     為避免子環的Hello報文在主環上形成環路，在子環的主節點上使能子環之前，請先在主環的主節點上使能主環。

·     缺省情況下，S6890係列交換機的接口處於ADM（Administratively Down）狀態，請根據實際需要在對應接口視圖下使用undo shutdown命令開啟接口。

5.5  配置步驟

5.5.1  Device A的配置

(1)     配置VLAN、MSTP實例和端口

# 創建VLAN 100～VLAN 200。

<DeviceA> system-view

[DeviceA] vlan 100 to 200

# VLAN 100～150映射到MSTI 1上，VLAN 151～200映射到MSTI 2上，並激活MST域的配置。

[DeviceA] stp region-configuration

[DeviceA-mst-region] instance 1 vlan 100 to 150

[DeviceA-mst-region] instance 2 vlan 151 to 200

[DeviceA-mst-region] active region-configuration

[DeviceA-mst-region] quit

# 將端口Ten-GigabitEthernet1/0/1和Ten-GigabitEthernet1/0/2配置為Trunk端口且允許VLAN 100～200通過，不允許VLAN 1通過，分別在端口上配置物理連接狀態up/down抑製時間為0秒（即不抑製），並關閉生成樹協議。

[DeviceA] interface ten-gigabitethernet 1/0/1

[DeviceA-Ten-GigabitEthernet1/0/1] port link-type trunk

[DeviceA-Ten-GigabitEthernet1/0/1] port trunk permit vlan 100 to 200

[DeviceA-Ten-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[DeviceA-Ten-GigabitEthernet1/0/1] link-delay 0 mode updown

[DeviceA-Ten-GigabitEthernet1/0/1] undo stp enable

[DeviceA-Ten-GigabitEthernet1/0/1] quit

[DeviceA] interface ten-gigabitethernet 1/0/2

[DeviceA-Ten-GigabitEthernet1/0/2] port link-type trunk

[DeviceA-Ten-GigabitEthernet1/0/2] port trunk permit vlan 100 to 200

[DeviceA-Ten-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[DeviceA-Ten-GigabitEthernet1/0/2] link-delay 0 mode updown

[DeviceA-Ten-GigabitEthernet1/0/2] undo stp enable

[DeviceA-Ten-GigabitEthernet1/0/2] quit

(2)     配置RRPP

# 創建RRPP域1。

[DeviceA] rrpp domain 1

# 配置域1的控製VLAN 1000，並將MSTI 1所映射的VLAN配置為該域的保護VLAN。

[DeviceA-rrpp-domain1] control-vlan 1000

[DeviceA-rrpp-domain1] protected-vlan reference-instance 1

# 配置Device A為主環主節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能主環。

[DeviceA-rrpp-domain1] ring 1 node-mode master primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 0

[DeviceA-rrpp-domain1] ring 1 enable

[DeviceA-rrpp-domain1] quit

# 創建RRPP域2。

[DeviceA] rrpp domain 2

# 配置域2的控製VLAN 2000，並將MSTI 2所映射的VLAN配置為該域的保護VLAN。

[DeviceA-rrpp-domain2] control-vlan 2000

[DeviceA-rrpp-domain2] protected-vlan reference-instance 2

# 配置Device A為主環傳輸節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能主環。

[DeviceA-rrpp-domain2] ring 1 node-mode transit primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 0

[DeviceA-rrpp-domain2] ring 1 enable

[DeviceA-rrpp-domain2] quit

# 全局使能RRPP。

[DeviceA] rrpp enable

5.5.2  Device B的配置

(1)     配置VLAN、MSTP實例和端口

# 創建VLAN 100～VLAN 200。

<DeviceB>system-view

[DeviceB] vlan 100 to 200

# VLAN 100～150映射到MSTI 1，VLAN 151～200映射到MSTI 2，並激活MST域的配置。

[DeviceB] stp region-configuration

[DeviceB-mst-region] instance 1 vlan 100 to 150

[DeviceB-mst-region] instance 2 vlan 151 to 200

[DeviceB-mst-region] active region-configuration

[DeviceB-mst-region] quit

# 將端口Ten-GigabitEthernet1/0/1和Ten-GigabitEthernet1/0/2配置為Trunk端口且允許VLAN 100～200通過，不允許VLAN 1通過，分別在端口上配置物理連接狀態up/down抑製時間為0秒（即不抑製），並關閉生成樹協議。

[DeviceB] interface ten-gigabitethernet 1/0/1

[DeviceB-Ten-GigabitEthernet1/0/1] port link-type trunk

[DeviceB-Ten-GigabitEthernet1/0/1] port trunk permit vlan 100 to 200

[DeviceB-Ten-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[DeviceB-Ten-GigabitEthernet1/0/1] link-delay 0 mode updown

[DeviceB-Ten-GigabitEthernet1/0/1] undo stp enable

[DeviceB-Ten-GigabitEthernet1/0/1] quit

[DeviceB] interface ten-gigabitethernet 1/0/2

[DeviceB-Ten-GigabitEthernet1/0/2] port link-type trunk

[DeviceB-Ten-GigabitEthernet1/0/2] port trunk permit vlan 100 to 200

[DeviceB-Ten-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[DeviceB-Ten-GigabitEthernet1/0/2] link-delay 0 mode updown

[DeviceB-Ten-GigabitEthernet1/0/2] undo stp enable

[DeviceB-Ten-GigabitEthernet1/0/2] quit

(2)     配置RRPP

# 創建RRPP域1。

[DeviceB] rrpp domain 1

# 配置域1的控製VLAN 1000，並將MSTI 1所映射的VLAN配置為該域的保護VLAN。

[DeviceB-rrpp-domain1] control-vlan 1000

[DeviceB-rrpp-domain1] protected-vlan reference-instance 1

# 配置Device B為主環傳輸節點，端口Ten-GigabitEthernet1/0/2為主端口，Ten-GigabitEthernet1/0/1為副端口，並使能主環。

[DeviceB-rrpp-domain1] ring 1 node-mode transit primary-port ten-gigabitethernet 1/0/2 secondary-port ten-gigabitethernet 1/0/1 level 0

[DeviceB-rrpp-domain1] ring 1 enable

[DeviceB-rrpp-domain1] quit

# 創建RRPP域2。

[DeviceB] rrpp domain 2

# 配置域2的控製VLAN 2000，並將MSTI 2所映射的VLAN配置為該域的保護VLAN。

[DeviceB-rrpp-domain2] control-vlan 2000

[DeviceB-rrpp-domain2] protected-vlan reference-instance 2

# 配置Device B為主環主節點，端口Ten-GigabitEthernet1/0/2為主端口，Ten-GigabitEthernet1/0/1為副端口，並使能主環。

[DeviceB-rrpp-domain2] ring 1 node-mode master primary-port ten-gigabitethernet 1/0/2 secondary-port ten-gigabitethernet 1/0/1 level 0

[DeviceB-rrpp-domain2] ring 1 enable

[DeviceB-rrpp-domain2] quit

# 全局使能RRPP。

[DeviceB] rrpp enable

5.5.3  Device C的配置

(1)     配置VLAN、MSTP實例和端口

# 創建VLAN 100～VLAN 200。

<DeviceC>system-view

[DeviceC] vlan 100 to 200

# VLAN 100～150映射到MSTI 1，VLAN 151～200映射到MSTI 2，並激活MST域的配置。

[DeviceC] stp region-configuration

[DeviceC-mst-region] instance 1 vlan 100 to 150

[DeviceC-mst-region] instance 2 vlan 151 to 200

[DeviceC-mst-region] active region-configuration

[DeviceC-mst-region] quit

# 將端口Ten-GigabitEthernet1/0/1~Ten-GigabitEthernet1/0/3配置為Trunk端口且允許VLAN 100～200通過，不允許VLAN 1通過，分別在端口上配置物理連接狀態up/down抑製時間為0秒（即不抑製），並關閉生成樹協議。

[DeviceC] interface ten-gigabitethernet 1/0/1

[DeviceC-Ten-GigabitEthernet1/0/1] port link-type trunk

[DeviceC-Ten-GigabitEthernet1/0/1] port trunk permit vlan 100 to 200

[DeviceC-Ten-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[DeviceC-Ten-GigabitEthernet1/0/1] link-delay 0 mode updown

[DeviceC-Ten-GigabitEthernet1/0/1] undo stp enable

[DeviceC-Ten-GigabitEthernet1/0/1] quit

[DeviceC] interface ten-gigabitethernet 1/0/2

[DeviceC-Ten-GigabitEthernet1/0/2] port link-type trunk

[DeviceC-Ten-GigabitEthernet1/0/2] port trunk permit vlan 100 to 200

[DeviceC-Ten-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[DeviceC-Ten-GigabitEthernet1/0/2] link-delay 0 mode updown

[DeviceC-Ten-GigabitEthernet1/0/2] undo stp enable

[DeviceC-Ten-GigabitEthernet1/0/2] quit

[DeviceC] interface ten-gigabitethernet 1/0/3

[DeviceC-Ten-GigabitEthernet1/0/3] port link-type trunk

[DeviceC-Ten-GigabitEthernet1/0/3] port trunk permit vlan 100 to 200

[DeviceC-Ten-GigabitEthernet1/0/3] undo port trunk permit vlan 1

[DeviceC-Ten-GigabitEthernet1/0/3] link-delay 0 mode updown

[DeviceC-Ten-GigabitEthernet1/0/3] undo stp enable

[DeviceC-Ten-GigabitEthernet1/0/3] quit

(2)     配置RRPP

# 創建RRPP域1。

[DeviceC] rrpp domain 1

# 配置域1的控製VLAN 1000，並將MSTI 1所映射的VLAN配置為該域的保護VLAN。

[DeviceC-rrpp-domain1] control-vlan 1000

[DeviceC-rrpp-domain1] protected-vlan reference-instance 1

# 配置Device C為主環傳輸節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能主環。

[DeviceC-rrpp-domain1] ring 1 node-mode transit primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 0

[DeviceC-rrpp-domain1] ring 1 enable

# 配置Device C為子環的邊緣節點，端口Ten-GigabitEthernet1/0/3為邊緣端口，並使能子環。

[DeviceC-rrpp-domain1] ring 2 node-mode edge edge-port ten-gigabitethernet 1/0/3

[DeviceC-rrpp-domain1] ring 2 enable

[DeviceC-rrpp-domain1] quit

# 創建RRPP域2。

[DeviceC] rrpp domain 2

# 配置域2的控製VLAN 2000，並將MSTI 2所映射的VLAN配置為該域的保護VLAN。

[DeviceC-rrpp-domain2] control-vlan 2000

[DeviceC-rrpp-domain2] protected-vlan reference-instance 2

# 配置Device C為主環傳輸節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能主環。

[DeviceC-rrpp-domain2] ring 1 node-mode transit primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 0

[DeviceC-rrpp-domain2] ring 1 enable

# 配置Device C為子環的邊緣節點，端口Ten-GigabitEthernet1/0/3為邊緣端口，並使能子環。

[DeviceC-rrpp-domain2] ring 2 node-mode edge edge-port ten-gigabitethernet 1/0/3

[DeviceC-rrpp-domain2] ring 2 enable

[DeviceC-rrpp-domain2] quit

# 全局使能RRPP。

[DeviceC] rrpp enable

5.5.4  Device D的配置

(1)     配置VLAN、MSTP實例和端口

# 創建VLAN 100～VLAN 200。

<DeviceD>system-view

[DeviceD] vlan 100 to 200

# VLAN 100～150映射到MSTI 1，VLAN 151～200映射到MSTI 2，並激活MST域的配置。

[DeviceD] stp region-configuration

[DeviceD-mst-region] instance 1 vlan 100 to 150

[DeviceD-mst-region] instance 2 vlan 151 to 200

[DeviceD-mst-region] active region-configuration

[DeviceD-mst-region] quit

# 將端口Ten-GigabitEthernet1/0/1~Ten-GigabitEthernet1/0/3配置為Trunk端口且允許VLAN 100～200通過，不允許VLAN 1通過，分別在端口上配置物理連接狀態up/down抑製時間為0秒（即不抑製），並關閉生成樹協議。

[DeviceD] interface ten-gigabitethernet 1/0/1

[DeviceD-Ten-GigabitEthernet1/0/1] port link-type trunk

[DeviceD-Ten-GigabitEthernet1/0/1] port trunk permit vlan 100 to 200

[DeviceD-Ten-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[DeviceD-Ten-GigabitEthernet1/0/1] link-delay 0 mode updown

[DeviceD-Ten-GigabitEthernet1/0/1] undo stp enable

[DeviceD-Ten-GigabitEthernet1/0/1] quit

[DeviceD] interface ten-gigabitethernet 1/0/2

[DeviceD-Ten-GigabitEthernet1/0/2] port link-type trunk

[DeviceD-Ten-GigabitEthernet1/0/2] port trunk permit vlan 100 to 200

[DeviceD-Ten-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[DeviceD-Ten-GigabitEthernet1/0/2] link-delay 0 mode updown

[DeviceD-Ten-GigabitEthernet1/0/2] undo stp enable

[DeviceD-Ten-GigabitEthernet1/0/2] quit

[DeviceD] interface ten-gigabitethernet 1/0/3

[DeviceD-Ten-GigabitEthernet1/0/3] port link-type trunk

[DeviceD-Ten-GigabitEthernet1/0/3] port trunk permit vlan 100 to 200

[DeviceD-Ten-GigabitEthernet1/0/3] undo port trunk permit vlan 1

[DeviceD-Ten-GigabitEthernet1/0/3] link-delay 0 mode updown

[DeviceD-Ten-GigabitEthernet1/0/3] undo stp enable

[DeviceD-Ten-GigabitEthernet1/0/3] quit

(2)     配置RRPP

# 創建RRPP域1。

[DeviceD] rrpp domain 1

# 配置域1的控製VLAN 1000，並將MSTI 1所映射的VLAN配置為該域的保護VLAN。

[DeviceD-rrpp-domain1] control-vlan 1000

[DeviceD-rrpp-domain1] protected-vlan reference-instance 1

# 配置Device D為主環傳輸節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能主環。

[DeviceD-rrpp-domain1] ring 1 node-mode transit primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 0

[DeviceD-rrpp-domain1] ring 1 enable

# 配置Device D為子環的輔助邊緣節點，端口Ten-GigabitEthernet1/0/3為邊緣端口，並使能子環。

[DeviceD-rrpp-domain1] ring 2 node-mode assistant-edge edge-port ten-gigabitethernet 1/0/3

[DeviceD-rrpp-domain1] ring 2 enable

[DeviceD-rrpp-domain1] quit

# 創建RRPP域2。

[DeviceD] rrpp domain 2

# 配置域2的控製VLAN 2000，並將MSTI 2所映射的VLAN配置為該域的保護VLAN。

[DeviceD-rrpp-domain2] control-vlan 2000

[DeviceD-rrpp-domain2] protected-vlan reference-instance 2

# 配置Device D為主環傳輸節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能主環。

[DeviceD-rrpp-domain2] ring 1 node-mode transit primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 0

[DeviceD-rrpp-domain2] ring 1 enable

# 配置Device D為子環的輔助邊緣節點，端口Ten-GigabitEthernet1/0/3為邊緣端口，並使能子環。

[DeviceD-rrpp-domain2] ring 2 node-mode assistant-edge edge-port ten-gigabitethernet 1/0/3

[DeviceD-rrpp-domain2] ring 2 enable

[DeviceD-rrpp-domain2] quit

# 全局使能RRPP。

[DeviceD] rrpp enable

5.5.5  Device E的配置

(1)     配置VLAN、MSTP實例和端口

# 創建VLAN 100～VLAN 200。

<DeviceE>system-view

[DeviceE] vlan 100 to 200

# VLAN 100～150映射到MSTI 1，VLAN 151～200映射到MSTI 2，並激活MST域的配置。

[DeviceE] stp region-configuration

[DeviceE-mst-region] instance 1 vlan 100 to 150

[DeviceE-mst-region] instance 2 vlan 151 to 200

[DeviceE-mst-region] active region-configuration

[DeviceE-mst-region] quit

# 將端口Ten-GigabitEthernet1/0/1和Ten-GigabitEthernet1/0/2配置為Trunk端口且允許VLAN 100～200通過，不允許VLAN 1通過，分別在端口上配置物理連接狀態up/down抑製時間為0秒（即不抑製），並關閉生成樹協議。

[DeviceE] interface ten-gigabitethernet 1/0/1

[DeviceE-Ten-GigabitEthernet1/0/1] port link-type trunk

[DeviceE-Ten-GigabitEthernet1/0/1] port trunk permit vlan 100 to 200

[DeviceE-Ten-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[DeviceE-Ten-GigabitEthernet1/0/1] link-delay 0 mode updown

[DeviceE-Ten-GigabitEthernet1/0/1] undo stp enable

[DeviceE-Ten-GigabitEthernet1/0/1] quit

[DeviceE] interface ten-gigabitethernet 1/0/2

[DeviceE-Ten-GigabitEthernet1/0/2] port link-type trunk

[DeviceE-Ten-GigabitEthernet1/0/2] port trunk permit vlan 100 to 200

[DeviceE-Ten-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[DeviceE-Ten-GigabitEthernet1/0/2] link-delay 0 mode updown

[DeviceE-Ten-GigabitEthernet1/0/2] undo stp enable

[DeviceE-Ten-GigabitEthernet1/0/2] quit

(2)     配置RRPP

# 創建RRPP域1。

[DeviceE] rrpp domain 1

# 配置域1的控製VLAN 1000，並將MSTI 1所映射的VLAN配置為該域的保護VLAN。

[DeviceE-rrpp-domain1] control-vlan 1000

[DeviceE-rrpp-domain1] protected-vlan reference-instance 1

# 配置Device E為子環主節點，端口Ten-GigabitEthernet1/0/2為主端口，Ten-GigabitEthernet1/0/1為副端口，並使能子環。

[DeviceE-rrpp-domain1] ring 2 node-mode master primary-port ten-gigabitethernet 1/0/2 secondary-port ten-gigabitethernet 1/0/1 level 1

[DeviceE-rrpp-domain1] ring 2 enable

[DeviceE-rrpp-domain1] quit

# 創建RRPP域2。

[DeviceE] rrpp domain 2

# 配置域2的控製VLAN 2000，並將MSTI 2所映射的VLAN配置為該域的保護VLAN。

[DeviceE-rrpp-domain2] control-vlan 2000

[DeviceE-rrpp-domain2] protected-vlan reference-instance 2

# 配置Device E為子環傳輸節點，端口Ten-GigabitEthernet1/0/2為主端口，Ten-GigabitEthernet1/0/1為副端口，並使能子環。

[DeviceE-rrpp-domain2] ring 2 node-mode transit primary-port ten-gigabitethernet 1/0/2 secondary-port ten-gigabitethernet 1/0/1 level 1

[DeviceE-rrpp-domain2] ring 2 enable

[DeviceE-rrpp-domain2] quit

# 全局使能RRPP。

[DeviceE] rrpp enable

5.5.6  Device F的配置

(1)     配置VLAN、MSTP實例和端口

# 創建VLAN 100～VLAN 200。

<DeviceF>system-view

[DeviceF] vlan 100 to 200

# VLAN 100～150映射到MSTI 1，VLAN 151～200映射到MSTI 2。

[DeviceF] stp region-configuration

[DeviceF-mst-region] instance 1 vlan 100 to 150

[DeviceF-mst-region] instance 2 vlan 151 to 200

[DeviceF-mst-region] active region-configuration

[DeviceF-mst-region] quit

# 將端口Ten-GigabitEthernet1/0/1和Ten-GigabitEthernet1/0/2配置為Trunk端口且允許VLAN 100～200通過，不允許VLAN 1通過，分別在端口上配置物理連接狀態up/down抑製時間為0秒（即不抑製），並關閉生成樹協議。

[DeviceF] interface ten-gigabitethernet 1/0/1

[DeviceF-Ten-GigabitEthernet1/0/1] port link-type trunk

[DeviceF-Ten-GigabitEthernet1/0/1] port trunk permit vlan 100 to 200

[DeviceF-Ten-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[DeviceF-Ten-GigabitEthernet1/0/1] link-delay 0 mode updown

[DeviceF-Ten-GigabitEthernet1/0/1] undo stp enable

[DeviceF-Ten-GigabitEthernet1/0/1] quit

[DeviceF] interface ten-gigabitethernet 1/0/2

[DeviceF-Ten-GigabitEthernet1/0/2] port link-type trunk

[DeviceF-Ten-GigabitEthernet1/0/2] port trunk permit vlan 100 to 200

[DeviceF-Ten-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[DeviceF-Ten-GigabitEthernet1/0/2] link-delay 0 mode updown

[DeviceF-Ten-GigabitEthernet1/0/2] undo stp enable

[DeviceF-Ten-GigabitEthernet1/0/2] quit

(2)     配置RRPP

# 創建RRPP域1。

[DeviceF] rrpp domain 1

# 配置域1的控製VLAN 1000，並將MSTI 1所映射的VLAN配置為該域的保護VLAN。

[DeviceF-rrpp-domain1] control-vlan 1000

[DeviceF-rrpp-domain1] protected-vlan reference-instance 1

# 配置Device F為子環傳輸節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能子環。

[DeviceF-rrpp-domain1] ring 2 node-mode transit primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 1

[DeviceF-rrpp-domain1] ring 2 enable

[DeviceF-rrpp-domain1] quit

# 創建RRPP域2。

[DeviceF] rrpp domain 2

# 配置域2的控製VLAN 2000，並將MSTI 2所映射的VLAN配置為該域的保護VLAN。

[DeviceF-rrpp-domain2] control-vlan 2000

[DeviceF-rrpp-domain2] protected-vlan reference-instance 2

# 配置Device F為子環主節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能子環。

[DeviceF-rrpp-domain2] ring 2 node-mode master primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 1

[DeviceF-rrpp-domain2] ring 2 enable

[DeviceF-rrpp-domain2] quit

# 全局使能RRPP。

[DeviceF] rrpp enable

5.6  驗證配置

# 查看Device A的RRPP域1詳細信息。

[DeviceA] display rrpp verbose domain 1

 Domain ID     : 1

Control VLAN  : Primary 1000, Secondary 1001

Protected VLAN: Reference instance 1

Hello timer   : 1 seconds, Fail timer: 3 seconds

Fast detection status: Disabled

Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Master

Ring State    : Completed

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                    Port status: UP

Secondary port: XGE1/0/2                    Port status: BLOCKED

顯示信息表示Device A在RRPP域1中為主環主節點，且RRPP域1中主環狀態為completed，主端口up，副端口blocked。

# 查看Device A的RRPP域2詳細信息。

[DeviceA] display rrpp verbose domain 2

 Domain ID     : 2

 Control VLAN  : Primary 2000, Secondary 2001

 Protected VLAN: Reference instance 2

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                    Port status: UP

Secondary port: XGE1/0/2                    Port status: UP

顯示信息表示Device A在RRPP域2中為主環傳輸節點，RRPP端口狀態均為up。

# 查看Device B的RRPP域1詳細信息。

[DeviceB] display rrpp verbose domain 1

 Domain ID     : 1

 Control VLAN  : Primary 1000, Secondary 1001

 Protected VLAN: Reference instance 1

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/2                    Port status: UP

Secondary port: XGE1/0/1                    Port status: UP

顯示信息表示Device B在RRPP域1中為主環傳輸節點，RRPP端口狀態均為up。

# 查看Device B的RRPP域2詳細信息。

[DeviceB] display rrpp verbose domain 2

 Domain ID     : 2

 Control VLAN  : Primary 2000, Secondary 2001

 Protected VLAN: Reference instance 2

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Master

Ring State    : Completed

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/2                    Port status: UP

Secondary port: XGE1/0/1                    Port status: BLOCKED

顯示信息表示Device B在RRPP域2中為主環主節點，且RRPP域2中主環狀態為completed，主端口up，副端口blocked。

# 查看Device C的RRPP域1詳細信息。

[DeviceC] display rrpp verbose domain 1

 Domain ID     : 1

 Control VLAN  : Primary 1000, Secondary 1001

 Protected VLAN: Reference instance 1

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                    Port status: UP

Secondary port: XGE1/0/2                    Port status: UP

 

Ring ID       : 2

Ring Level    : 1

Node Mode     : Edge

Ring State    : -

Enable Status : Yes    Active Status: Yes

Common port   : XGE1/0/1                    Port status: UP

                XGE1/0/2                    Port status: UP

Edge port     : XGE1/0/3                    Port status: UP

顯示信息表示Device C在RRPP域1中為主環傳輸節點和子環邊緣節點，RRPP端口狀態均為up。

# 查看Device C的RRPP域2詳細信息。

[DeviceC] display rrpp verbose domain 2

 Domain ID     : 2

 Control VLAN  : Primary 2000, Secondary 2001

 Protected VLAN: Reference instance 2

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                    Port status: UP

Secondary port: XGE1/0/2                    Port status: UP

 

Ring ID       : 2

Ring Level    : 1

Node Mode     : Edge

Ring State    : -

Enable Status : Yes    Active Status: Yes

Common port   : XGE1/0/1                    Port status: UP

                XGE1/0/2                    Port status: UP

Edge port     : XGE1/0/3                    Port status: UP

顯示信息表示Device C在RRPP域2中為主環傳輸節點和子環邊緣節點，RRPP端口狀態均為up。

# 查看Device D的RRPP域1詳細信息。

[DeviceD] display rrpp verbose domain 1

 Domain ID     : 1

 Control VLAN  : Primary 1000, Secondary 1001

 Protected VLAN: Reference instance 1

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                    Port status: UP

Secondary port: XGE1/0/2                    Port status: UP

 

Ring ID       : 2

Ring Level    : 1

Node Mode     : Assistant-edge

Ring State    : -

Enable Status : Yes    Active Status: Yes

Common port   : XGE1/0/1                    Port status: UP

                XGE1/0/2                    Port status: UP

Edge port     : XGE1/0/3                    Port status: UP

顯示信息表示Device C在RRPP域1中為主環傳輸節點和子環輔助邊緣節點，RRPP端口狀態均為up。

# 查看Device D的RRPP域2詳細信息。

[DeviceD] display rrpp verbose domain 2

 Domain ID     : 2

 Control VLAN  : Primary 2000, Secondary 2001

 Protected VLAN: Reference instance 2

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                    Port status: UP

Secondary port: XGE1/0/2                    Port status: UP

 

Ring ID       : 2

Ring Level    : 1

Node Mode     : Assistant-edge

Ring State    : -

Enable Status : Yes    Active Status: Yes

Common port   : XGE1/0/1                    Port status: UP

                XGE1/0/2                    Port status: UP

Edge port     : XGE1/0/3                    Port status: UP

顯示信息表示Device C在RRPP域2中為主環傳輸節點和子環輔助邊緣節點，RRPP端口狀態均為up。

# 查看Device E的RRPP域1詳細信息。

[DeviceE] display rrpp verbose domain 1

 Domain ID     : 1

 Control VLAN  : Primary 1000, Secondary 1001

 Protected VLAN: Reference instance 1

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 2

Ring Level    : 1

Node Mode     : Master

Ring State    : Completed

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/2                    Port status: UP

Secondary port: XGE1/0/1                    Port status: BLOCKED

顯示信息表示Device E在RRPP域1中為子環主節點，且RRPP域1中子環狀態為completed，主端口up，副端口blocked。

# 查看Device E的RRPP域2詳細信息。

[DeviceE] display rrpp verbose domain 2

 Domain ID     : 2

 Control VLAN  : Primary 2000, Secondary 2001

 Protected VLAN: Reference instance 2

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 2

Ring Level    : 1

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/2                    Port status: UP

Secondary port: XGE1/0/1                    Port status: UP

顯示信息表示Device E在RRPP域2中為子環傳輸節點，RRPP端口狀態均為up。

# 查看Device F的RRPP域1詳細信息。

[DeviceF] display rrpp verbose domain 1

 Domain ID     : 1

 Control VLAN  : Primary 1000, Secondary 1001

 Protected VLAN: Reference instance 1

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 2

Ring Level    : 1

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                    Port status: UP

Secondary port: XGE1/0/2                    Port status: UP

顯示信息表示Device F在RRPP域1中為子環傳輸節點，RRPP端口狀態均為up。

# 查看Device F的RRPP域2詳細信息。

[DeviceF] display rrpp verbose domain 2

 Domain ID     : 2

 Control VLAN  : Primary 2000, Secondary 2001

 Protected VLAN: Reference instance 2

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 2

Ring Level    : 1

Node Mode     : Master

Ring State    : Completed

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                    Port status: UP

Secondary port: XGE1/0/2                    Port status: BLOCKED

顯示信息表示Device F在RRPP域2中為子環主節點，且RRPP域2中子環狀態為completed，主端口up，副端口blocked。

5.7  配置文件

·     Device A：

#

 sysname DeviceA

#

vlan 1

#

vlan 100 to 200

#

stp region-configuration

 instance 1 vlan 100 to 150

 instance 2 vlan 151 to 200

 active region-configuration

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

rrpp domain 1

 control-vlan 1000

 protected-vlan reference-instance 1

 ring 1 node-mode master primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 0

 ring 1 enable

#

rrpp domain 2

 control-vlan 2000

 protected-vlan reference-instance 2

 ring 1 node-mode transit primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 0

 ring 1 enable

#

rrpp enable

#

·     Device B：

#

 sysname DeviceB

#

vlan 1

#

vlan 100 to 200

#

stp region-configuration

 instance 1 vlan 100 to 150

 instance 2 vlan 151 to 200

 active region-configuration

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

rrpp domain 1

 control-vlan 1000

 protected-vlan reference-instance 1

 ring 1 node-mode transit primary-port Ten-GigabitEthernet1/0/2 secondary-port Ten-GigabitEthernet1/0/1 level 0

 ring 1 enable

#

rrpp domain 2

 control-vlan 2000

 protected-vlan reference-instance 2

 ring 1 node-mode master primary-port Ten-GigabitEthernet1/0/2 secondary-port Ten-GigabitEthernet1/0/1 level 0

 ring 1 enable

#

rrpp enable

#

·     Device C：

#

 sysname DeviceC

#

vlan 1

#

vlan 100 to 200

#

stp region-configuration

 instance 1 vlan 100 to 150

 instance 2 vlan 151 to 200

 active region-configuration

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/3

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

rrpp domain 1

 control-vlan 1000

 protected-vlan reference-instance 1

 ring 1 node-mode transit primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 0

 ring 1 enable

 ring 2 node-mode edge edge-port Ten-GigabitEthernet1/0/3

 ring 2 enable

#

rrpp domain 2

 control-vlan 2000

 protected-vlan reference-instance 2

 ring 1 node-mode transit primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 0

 ring 1 enable

 ring 2 node-mode edge edge-port Ten-GigabitEthernet1/0/3

 ring 2 enable

#

rrpp enable

#

·     Device D：

#

 sysname DeviceD

#

vlan 1

#

vlan 100 to 200

#

stp region-configuration

 instance 1 vlan 100 to 150

 instance 2 vlan 151 to 200

 active region-configuration

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/3

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

rrpp domain 1

 control-vlan 1000

 protected-vlan reference-instance 1

 ring 1 node-mode transit primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 0

 ring 1 enable

 ring 2 node-mode assistant-edge edge-port Ten-GigabitEthernet1/0/3

 ring 2 enable

#

rrpp domain 2

 control-vlan 2000

 protected-vlan reference-instance 2

 ring 1 node-mode transit primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 0

 ring 1 enable

 ring 2 node-mode assistant-edge edge-port Ten-GigabitEthernet1/0/3

 ring 2 enable

#

rrpp enable

#

·     Device E：

#

 sysname DeviceE

#

vlan 1

#

vlan 100 to 200

#

stp region-configuration

 instance 1 vlan 100 to 150

 instance 2 vlan 151 to 200

 active region-configuration

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

rrpp domain 1

 control-vlan 1000

 protected-vlan reference-instance 1

 ring 2 node-mode master primary-port Ten-GigabitEthernet1/0/2 secondary-port Ten-GigabitEthernet1/0/1 level 1

 ring 2 enable

#

rrpp domain 2

 control-vlan 2000

 protected-vlan reference-instance 2

 ring 2 node-mode transit primary-port Ten-GigabitEthernet1/0/2 secondary-port Ten-GigabitEthernet1/0/1 level 1

 ring 2 enable

#

rrpp enable

#

·     Device F：

#

 sysname DeviceF

#

vlan 1

#

vlan 100 to 200

#

stp region-configuration

 instance 1 vlan 100 to 150

 instance 2 vlan 151 to 200

 active region-configuration

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

rrpp domain 1

 control-vlan 1000

 protected-vlan reference-instance 1

 ring 2 node-mode transit primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 1

 ring 2 enable

#

rrpp domain 2

 control-vlan 2000

 protected-vlan reference-instance 2

 ring 2 node-mode master primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 1

 ring 2 enable

#

rrpp enable

#

6  RRPP雙歸屬環+相切環配置舉例

6.1  組網需求

如圖5所示，小區用戶通過接入層設備以環網網絡的形式接入彙聚層，彙聚層網絡也是一個環網。該網絡中使用VLAN 100～150承載語音業務、VLAN 151～200承載視頻業務。要求通過配置RRPP和以太網接口連接狀態抑製功能，實現如下需求：

·     二層網絡的環路預防和鏈路恢複功能。

·     使語音和視頻流量走不同的網絡拓撲，以實現鏈路的負載分擔。

·     設置所有環上以太網端口的物理連接狀態抑製時間為0秒，以提高RRPP的拓撲變化收斂速度。

·     減少Edge-Hello報文的收發數量。

圖5 RRPP多子環配置組網圖

 

6.2  配置思路

·     將整個網絡劃分成一個雙歸屬環和一個單環。RRPP主環需要透傳子環的保護VLAN和控製VLAN內的流量，需要有較強的數據傳輸能力。本案例選擇彙聚層環網作為主環（Ring 1），接入層環網分別作為子環（Ring 2和Ring 3）以及雙歸屬環的相切環（Ring 4）。

·     為了實現語音和視頻流量走不同的拓撲，雙歸屬環和單環分別劃分為兩個RRPP域：雙歸屬環的域1和單環的域4保護承載語音流量的VLAN 100～150，Ring 1主節點為Device A，Ring 2主節點為Device E，Ring 3主節點為Device F，Ring 4的主節點為Device H；雙歸屬環的域2和單環的域3保護承載視頻流量的VLAN 151～200，Ring 1主節點為Device B，Ring 2主節點為Device E，Ring 3主節點為Device F，Ring 4的主節點為Device H。

·     為了實現語音和視頻流量的鏈路的負載分擔，選擇Device A的Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口；Device B的Ten-GigabitEthernet1/0/2為主端口，Ten-GigabitEthernet1/0/1為副端口；Device E的Ten-GigabitEthernet1/0/1在域1中為副端口、在域2中為主端口，Ten-GigabitEthernet1/0/2在域1中為主端口、在域2中為副端口；Device F的Ten-GigabitEthernet1/0/1在域1中為副端口、在域2中為主端口，Ten-GigabitEthernet1/0/2在域1中為主端口、在域2中為副端口；Device H的Ten-GigabitEthernet1/0/1在域3中為主端口、在域4中為副端口，Ten-GigabitEthernet1/0/2在域3中為副端口、在域4中為主端口。語音流量和視頻流量的拓撲如圖6所示。

·     為了減少Edge-Hello報文的收發數量，用戶可以采用環組機製，即將具有相同邊緣節點／輔助邊緣節點的一組子環加入環組。本例中將域1和域2的兩個子環（Ring 2和Ring 3）分別都加入環組。

圖6 流量拓撲示意圖

 

6.3  使用版本

本舉例是在S6890-CMW710-R2712版本上進行配置和驗證的。

6.4  配置注意事項

·     在雙歸屬環組網中，為避免主環故障時出現臨時環路，應確保子環主節點與主環主節點上的Fail定時器取值之差大於子環主節點上Hello定時器取值的2倍。

·     配置邊緣節點和輔助邊緣節點時，必須先配置主環再配置子環。

·     配置好RRPP環之後不再允許用戶刪除或修改控製VLAN。控製VLAN隻能通過undo control-vlan命令刪除，不能通過undo vlan命令刪除。

·     在配置負載分擔時，不同RRPP域的保護VLAN必須不同。

·     在一台設備上使能子環之前必須先使能主環，而關閉主環之前也必須先關閉所有子環，否則係統將提示出錯。

·     如果一台設備處於同一RRPP域的多個RRPP環上，則該設備在子環上的節點角色隻能是邊緣節點或輔助邊緣節點。

·     為避免子環的Hello報文在主環上形成環路，在子環的主節點上使能子環之前，請先在主環的主節點上使能主環。

·     同一環組中的子環所對應主環的鏈路必須相同，並且一個子環隻能屬於一個環組，配置在邊緣節點和輔助邊緣節點上的環組中所包含的子環必須相同，否則環組不能正常工作。

·     邊緣節點環組及其對應的輔助邊緣節點環組的配置和激活狀態必須相同。

·     缺省情況下，S6890係列交換機的接口處於ADM（Administratively Down）狀態，請根據實際需要在對應接口視圖下使用undo shutdown命令開啟接口。

6.5  配置步驟

6.5.1  Device A的配置

(1)     配置VLAN、MSTP實例和端口

# 創建VLAN 100～VLAN 200。

<DeviceA> system-view

[DeviceA] vlan 100 to 200

# VLAN 100～150映射到MSTI 1，VLAN 151～200映射到MSTI 2。

[DeviceA] stp region-configuration

[DeviceA-mst-region] instance 1 vlan 100 to 150

[DeviceA-mst-region] instance 2 vlan 151 to 200

[DeviceA-mst-region] active region-configuration

[DeviceA-mst-region] quit

# 將端口Ten-GigabitEthernet1/0/1和Ten-GigabitEthernet1/0/2配置為Trunk端口且允許VLAN 100～200通過，不允許VLAN 1通過，分別在端口上配置物理連接狀態up/down抑製時間為0秒（即不抑製），並關閉生成樹協議。

[DeviceA] interface ten-gigabitethernet 1/0/1

[DeviceA-Ten-GigabitEthernet1/0/1] port link-type trunk

[DeviceA-Ten-GigabitEthernet1/0/1] port trunk permit vlan 100 to 200

[DeviceA-Ten-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[DeviceA-Ten-GigabitEthernet1/0/1] link-delay 0 mode updown

[DeviceA-Ten-GigabitEthernet1/0/1] undo stp enable

[DeviceA-Ten-GigabitEthernet1/0/1] quit

[DeviceA] interface ten-gigabitethernet 1/0/2

[DeviceA-Ten-GigabitEthernet1/0/2] port link-type trunk

[DeviceA-Ten-GigabitEthernet1/0/2] port trunk permit vlan 100 to 200

[DeviceA-Ten-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[DeviceA-Ten-GigabitEthernet1/0/2] link-delay 0 mode updown

[DeviceA-Ten-GigabitEthernet1/0/2] undo stp enable

[DeviceA-Ten-GigabitEthernet1/0/2] quit

(2)     配置RRPP

# 創建RRPP域1。

[DeviceA] rrpp domain 1

# 配置域1的控製VLAN 1000，並將MSTI 1所映射的VLAN配置為該域的保護VLAN。

[DeviceA-rrpp-domain1] control-vlan 1000

[DeviceA-rrpp-domain1] protected-vlan reference-instance 1

# 配置Device A為主環主節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能主環。

[DeviceA-rrpp-domain1] ring 1 node-mode master primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 0

[DeviceA-rrpp-domain1] ring 1 enable

[DeviceA-rrpp-domain1] quit

# 創建RRPP域2。

[DeviceA] rrpp domain 2

# 配置域2的控製VLAN 2000，並將MSTI 2所映射的VLAN配置為該域的保護VLAN。

[DeviceA-rrpp-domain2] control-vlan 2000

[DeviceA-rrpp-domain2] protected-vlan reference-instance 2

# 配置Device A為主環傳輸節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能主環。

[DeviceA-rrpp-domain2] ring 1 node-mode transit primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 0

[DeviceA-rrpp-domain2] ring 1 enable

[DeviceA-rrpp-domain2] quit

# 全局使能RRPP。

[DeviceA] rrpp enable

6.5.2  Device B的配置

(1)     配置VLAN、MSTP實例和端口

# 創建VLAN 100～VLAN 200。

<DeviceB>system-view

[DeviceB] vlan 100 to 200

# VLAN 100～150映射到MSTI 1，VLAN 151～200映射到MSTI 2。

[DeviceB] stp region-configuration

[DeviceB-mst-region] instance 1 vlan 100 to 150

[DeviceB-mst-region] instance 2 vlan 151 to 200

[DeviceB-mst-region] active region-configuration

[DeviceB-mst-region] quit

# 將端口Ten-GigabitEthernet1/0/1和Ten-GigabitEthernet1/0/2配置為Trunk端口且允許VLAN 100～200通過，不允許VLAN 1通過，分別在端口上配置物理連接狀態up/down抑製時間為0秒（即不抑製），並關閉生成樹協議。

[DeviceB] interface ten-gigabitethernet 1/0/1

[DeviceB-Ten-GigabitEthernet1/0/1] port link-type trunk

[DeviceB-Ten-GigabitEthernet1/0/1] port trunk permit vlan 100 to 200

[DeviceB-Ten-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[DeviceB-Ten-GigabitEthernet1/0/1] link-delay 0 mode updown

[DeviceB-Ten-GigabitEthernet1/0/1] undo stp enable

[DeviceB-Ten-GigabitEthernet1/0/1] quit

[DeviceB] interface ten-gigabitethernet 1/0/2

[DeviceB-Ten-GigabitEthernet1/0/2] port link-type trunk

[DeviceB-Ten-GigabitEthernet1/0/2] port trunk permit vlan 100 to 200

[DeviceB-Ten-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[DeviceB-Ten-GigabitEthernet1/0/2] link-delay 0 mode updown

[DeviceB-Ten-GigabitEthernet1/0/2] undo stp enable

[DeviceB-Ten-GigabitEthernet1/0/2] quit

(2)     配置RRPP

# 創建RRPP域1。

[DeviceB] rrpp domain 1

# 配置域1的控製VLAN 1000，並將MSTI 1所映射的VLAN配置為該域的保護VLAN。

[DeviceB-rrpp-domain1] control-vlan 1000

[DeviceB-rrpp-domain1] protected-vlan reference-instance 1

# 配置Device B為主環傳輸節點，端口Ten-GigabitEthernet1/0/2為主端口，Ten-GigabitEthernet1/0/1為副端口，並使能主環。

[DeviceB-rrpp-domain1] ring 1 node-mode transit primary-port ten-gigabitethernet 1/0/2 secondary-port ten-gigabitethernet 1/0/1 level 0

[DeviceB-rrpp-domain1] ring 1 enable

[DeviceB-rrpp-domain1] quit

# 創建RRPP域2。

[DeviceB] rrpp domain 2

# 配置域2的控製VLAN 2000，並將MSTI 2所映射的VLAN配置為該域的保護VLAN。

[DeviceB-rrpp-domain2] control-vlan 2000

[DeviceB-rrpp-domain2] protected-vlan reference-instance 2

# 配置Device B為主環主節點，端口Ten-GigabitEthernet1/0/2為主端口，Ten-GigabitEthernet1/0/1為副端口，並使能主環。

[DeviceB-rrpp-domain2] ring 1 node-mode master primary-port ten-gigabitethernet 1/0/2 secondary-port ten-gigabitethernet 1/0/1 level 0

[DeviceB-rrpp-domain2] ring 1 enable

[DeviceB-rrpp-domain2] quit

# 全局使能RRPP。

[DeviceB] rrpp enable

6.5.3  Device C的配置

(1)     配置VLAN、MSTP實例和端口

# 創建VLAN 100～VLAN 200。

<DeviceC>system-view

[DeviceC] vlan 100 to 200

# VLAN 100～150映射到MSTI 1，VLAN 151～200映射到MSTI 2。

[DeviceC] stp region-configuration

[DeviceC-mst-region] instance 1 vlan 100 to 150

[DeviceC-mst-region] instance 2 vlan 151 to 200

[DeviceC-mst-region] active region-configuration

[DeviceC-mst-region] quit

# 將端口Ten-GigabitEthernet1/0/1~Ten-GigabitEthernet1/0/4配置為Trunk端口且允許VLAN 100～200通過，不允許VLAN 1通過，分別在端口上配置物理連接狀態up/down抑製時間為0秒（即不抑製），並關閉生成樹協議。

[DeviceC] interface range ten-gigabitethernet 1/0/1 to ten-gigabitethernet 1/0/4

[DeviceC-if-range] port link-type trunk

[DeviceC-if-range] port trunk permit vlan 100 to 200

[DeviceC-if-range] undo port trunk permit vlan 1

[DeviceC-if-range] link-delay 0 mode updown

[DeviceC-if-range] undo stp enable

[DeviceC-if-range] quit

(2)     配置RRPP

# 創建RRPP域1。

[DeviceC] rrpp domain 1

# 配置域1的控製VLAN 1000，並將MSTI 1所映射的VLAN配置為該域的保護VLAN。

[DeviceC-rrpp-domain1] control-vlan 1000

[DeviceC-rrpp-domain1] protected-vlan reference-instance 1

# 配置Device C為主環傳輸節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能主環。

[DeviceC-rrpp-domain1] ring 1 node-mode transit primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 0

[DeviceC-rrpp-domain1] ring 1 enable

# 配置Device C為子環（Ring 2）的邊緣節點，端口Ten-GigabitEthernet1/0/3為邊緣端口，並使能子環。

[DeviceC-rrpp-domain1] ring 2 node-mode edge edge-port ten-gigabitethernet 1/0/3

[DeviceC-rrpp-domain1] ring 2 enable

# 配置Device C為子環（Ring 3）的邊緣節點，端口Ten-GigabitEthernet1/0/4為邊緣端口，並使能子環。

[DeviceC-rrpp-domain1] ring 3 node-mode edge edge-port ten-gigabitethernet 1/0/4

[DeviceC-rrpp-domain1] ring 3 enable

[DeviceC-rrpp-domain1] quit

# 創建RRPP域2。

[DeviceC] rrpp domain 2

# 配置域2的控製VLAN 2000，並將MSTI 2所映射的VLAN配置為該域的保護VLAN。

[DeviceC-rrpp-domain2] control-vlan 2000

[DeviceC-rrpp-domain2] protected-vlan reference-instance 2

# 配置Device C為主環傳輸節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能主環。

[DeviceC-rrpp-domain2] ring 1 node-mode transit primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 0

[DeviceC-rrpp-domain2] ring 1 enable

# 配置Device C為子環（Ring 2）的邊緣節點，端口Ten-GigabitEthernet1/0/3為邊緣端口，並使能子環。

[DeviceC-rrpp-domain2] ring 2 node-mode edge edge-port ten-gigabitethernet 1/0/3

[DeviceC-rrpp-domain2] ring 2 enable

# 配置Device C為子環（Ring 3）的邊緣節點，端口Ten-GigabitEthernet1/0/4為邊緣端口，並使能子環。

[DeviceC-rrpp-domain2] ring 3 node-mode edge edge-port ten-gigabitethernet 1/0/4

[DeviceC-rrpp-domain2] ring 3 enable

[DeviceC-rrpp-domain2] quit

# 配置環組，將域1和域2的兩個子環都加入環組。

[DeviceC] rrpp ring-group 1

[DeviceC-ring-group1] domain 1 ring 2 3

[DeviceC-ring-group1] domain 2 ring 2 3

[DeviceC-ring-group1] quit

# 全局使能RRPP。

[DeviceC] rrpp enable

6.5.4  Device D的配置

(1)     配置VLAN、MSTP實例和端口

# 創建VLAN 100～VLAN 200

<DeviceD> system-view

[DeviceD] vlan 100 to 200

# VLAN 100～150映射到MSTI 1，VLAN 151～200映射到MSTI 2。

[DeviceD] stp region-configuration

[DeviceD-mst-region] instance 1 vlan 100 to 150

[DeviceD-mst-region] instance 2 vlan 151 to 200

[DeviceD-mst-region] active region-configuration

[DeviceD-mst-region] quit

# 將端口Ten-GigabitEthernet1/0/1~Ten-GigabitEthernet1/0/6配置為Trunk端口且允許VLAN 100～200通過，不允許VLAN 1通過，分別在端口上配置物理連接狀態up/down抑製時間為0秒（即不抑製），並關閉生成樹協議。

[DeviceD] interface range ten-gigabitethernet 1/0/1 to ten-gigabitethernet 1/0/6

[DeviceD-if-range] port link-type trunk

[DeviceD-if-range] port trunk permit vlan 100 to 200

[DeviceD-if-range] undo port trunk permit vlan 1

[DeviceD-if-range] link-delay 0 mode updown

[DeviceD-if-range] undo stp enable

[DeviceD-if-range] quit

(2)     配置RRPP

# 創建RRPP域1。

[DeviceD] rrpp domain 1

# 配置域1的控製VLAN 1000，並將MSTI 1所映射的VLAN配置為該域的保護VLAN。

[DeviceD-rrpp-domain1] control-vlan 1000

[DeviceD-rrpp-domain1] protected-vlan reference-instance 1

# 配置Device D為主環傳輸節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能主環。

[DeviceD-rrpp-domain1] ring 1 node-mode transit primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 0

[DeviceD-rrpp-domain1] ring 1 enable

# 配置Device D為子環（Ring 2）的輔助邊緣節點，端口Ten-GigabitEthernet1/0/3為邊緣端口，並使能子環。

[DeviceD-rrpp-domain1] ring 2 node-mode assistant-edge edge-port ten-gigabitethernet 1/0/3

[DeviceD-rrpp-domain1] ring 2 enable

# 配置Device D為子環（Ring 3）的輔助邊緣節點，端口Ten-GigabitEthernet1/0/4為邊緣端口，並使能子環。

[DeviceD-rrpp-domain1] ring 3 node-mode assistant-edge edge-port ten-gigabitethernet 1/0/4

[DeviceD-rrpp-domain1] ring 3 enable

[DeviceD-rrpp-domain1] quit

# 創建RRPP域2。

[DeviceD] rrpp domain 2

# 配置域2的控製VLAN 2000，並將MSTI 2所映射的VLAN配置為該域的保護VLAN。

[DeviceD-rrpp-domain2] control-vlan 2000

[DeviceD-rrpp-domain2] protected-vlan reference-instance 2

# 配置Device D為主環傳輸節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能主環。

[DeviceD-rrpp-domain2] ring 1 node-mode transit primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 0

[DeviceD-rrpp-domain2] ring 1 enable

# 配置Device D為子環（Ring 2）的輔助邊緣節點，端口Ten-GigabitEthernet1/0/3為邊緣端口，並使能子環。

[DeviceD-rrpp-domain2] ring 2 node-mode assistant-edge edge-port ten-gigabitethernet 1/0/3

[DeviceD-rrpp-domain2] ring 2 enable

# 配置Device D為子環（Ring 3）的輔助邊緣節點，端口Ten-GigabitEthernet1/0/4為邊緣端口，並使能子環。

[DeviceD-rrpp-domain2] ring 3 node-mode assistant-edge edge-port ten-gigabitethernet 1/0/4

[DeviceD-rrpp-domain2] ring 3 enable

[DeviceD-rrpp-domain2] quit

# 創建RRPP域3。

[DeviceD] rrpp domain 3

# 配置域3的控製VLAN 3000，並將MSTI 1所映射的VLAN配置為該域的保護VLAN。

[DeviceD-rrpp-domain3] control-vlan 3000

[DeviceD-rrpp-domain3] protected-vlan reference-instance 1

# 配置Device D為主環傳輸節點，端口Ten-GigabitEthernet1/0/5為主端口，Ten-GigabitEthernet1/0/6為副端口，並使能主環。

[DeviceD-rrpp-domain1] ring 4 node-mode transit primary-port ten-gigabitethernet 1/0/5 secondary-port ten-gigabitethernet 1/0/6 level 0

[DeviceD-rrpp-domain1] ring 4 enable

[DeviceD-rrpp-domain1] quit

# 創建RRPP域4。

[DeviceD] rrpp domain 4

# 配置域4的控製VLAN 4000，並將MSTI 2所映射的VLAN配置為該域的保護VLAN。

[DeviceD-rrpp-domain4] control-vlan 4000

[DeviceD-rrpp-domain4] protected-vlan reference-instance 2

# 配置Device D為主環傳輸節點，端口Ten-GigabitEthernet1/0/5為主端口，Ten-GigabitEthernet1/0/6為副端口，並使能主環。

[DeviceD-rrpp-domain4] ring 4 node-mode transit primary-port ten-gigabitethernet 1/0/5 secondary-port ten-gigabitethernet 1/0/6 level 0

[DeviceD-rrpp-domain4] ring 4 enable

[DeviceD-rrpp-domain4] quit

# 配置環組，將域1和域2的兩個子環都加入環組。

[DeviceD] rrpp ring 1

[DeviceD-ring-group1] domain 1 ring 2 3

[DeviceD-ring-group1] domain 2 ring 2 3

[DeviceD-ring-group1] quit

# 全局使能RRPP。

[DeviceD] rrpp enable

6.5.5  Device E的配置

(1)     配置VLAN、MSTP實例和端口

# 創建VLAN 100～VLAN 200。

<DeviceE> system-view

[DeviceE] vlan 100 to 200

# VLAN 100～150映射到MSTI 1，VLAN 151～200映射到MSTI 2。

[DeviceE] stp region-configuration

[DeviceE-mst-region] instance 1 vlan 100 to 150

[DeviceE-mst-region] instance 2 vlan 151 to 200

[DeviceE-mst-region] active region-configuration

[DeviceE-mst-region] quit

# 將端口Ten-GigabitEthernet1/0/1和Ten-GigabitEthernet1/0/2配置為Trunk端口且允許VLAN 100～200通過，不允許VLAN 1通過，分別在端口上配置物理連接狀態up/down抑製時間為0秒（即不抑製），並關閉生成樹協議。

[DeviceE] interface ten-gigabitethernet 1/0/1

[DeviceE-Ten-GigabitEthernet1/0/1] port link-type trunk

[DeviceE-Ten-GigabitEthernet1/0/1] port trunk permit vlan 100 to 200

[DeviceE-Ten-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[DeviceE-Ten-GigabitEthernet1/0/1] link-delay 0 mode updown

[DeviceE-Ten-GigabitEthernet1/0/1] undo stp enable

[DeviceE-Ten-GigabitEthernet1/0/1] quit

[DeviceE] interface ten-gigabitethernet 1/0/2

[DeviceE-Ten-GigabitEthernet1/0/2] port link-type trunk

[DeviceE-Ten-GigabitEthernet1/0/2] port trunk permit vlan 100 to 200

[DeviceE-Ten-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[DeviceE-Ten-GigabitEthernet1/0/2] link-delay 0 mode updown

[DeviceE-Ten-GigabitEthernet1/0/2] undo stp enable

[DeviceE-Ten-GigabitEthernet1/0/2] quit

(2)     配置RRPP

# 創建RRPP域1。

[DeviceE] rrpp domain 1

# 配置域1的控製VLAN 1000，並將MSTI 1所映射的VLAN配置為該域的保護VLAN。

[DeviceE-rrpp-domain1] control-vlan 1000

[DeviceE-rrpp-domain1] protected-vlan reference-instance 1

# 配置Device E為子環2的主節點，端口Ten-GigabitEthernet1/0/2為主端口，Ten-GigabitEthernet1/0/1為副端口，並使能子環。

[DeviceE-rrpp-domain1] ring 2 node-mode master primary-port ten-gigabitethernet 1/0/2 secondary-port ten-gigabitethernet 1/0/1 level 1

[DeviceE-rrpp-domain1] ring 2 enable

[DeviceE-rrpp-domain1] quit

# 創建RRPP域2。

[DeviceE] rrpp domain 2

# 配置域2的控製VLAN 2000，並將MSTI 2所映射的VLAN配置為該域的保護VLAN。

[DeviceE-rrpp-domain2] control-vlan 2000

[DeviceE-rrpp-domain2] protected-vlan reference-instance 2

# 配置Device E為子環2的主節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能子環。

[DeviceE-rrpp-domain2] ring 2 node-mode master primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 1

[DeviceE-rrpp-domain2] ring 2 enable

[DeviceE-rrpp-domain2] quit

# 全局使能RRPP。

[DeviceE] rrpp enable

6.5.6  Device F的配置

(1)     配置VLAN、MSTP實例和端口

# 創建VLAN 100～VLAN 200。

<DeviceF> system-view

[DeviceF] vlan 100 to 200

# VLAN 100～150映射到MSTI 1，VLAN 151～200映射到MSTI 2。

[DeviceF] stp region-configuration

[DeviceF-mst-region] instance 1 vlan 100 to 150

[DeviceF-mst-region] instance 2 vlan 151 to 200

[DeviceF-mst-region] active region-configuration

[DeviceF-mst-region] quit

# 將端口Ten-GigabitEthernet1/0/1和Ten-GigabitEthernet1/0/2配置為Trunk端口且允許VLAN 100～200通過，不允許VLAN 1通過，分別在端口上配置物理連接狀態up/down抑製時間為0秒（即不抑製），並關閉生成樹協議。

[DeviceF] interface ten-gigabitethernet 1/0/1

[DeviceF-Ten-GigabitEthernet1/0/1] port link-type trunk

[DeviceF-Ten-GigabitEthernet1/0/1] port trunk permit vlan 100 to 200

[DeviceF-Ten-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[DeviceF-Ten-GigabitEthernet1/0/1] link-delay 0 mode updown

[DeviceF-Ten-GigabitEthernet1/0/1] undo stp enable

[DeviceF-Ten-GigabitEthernet1/0/1] quit

[DeviceF] interface ten-gigabitethernet 1/0/2

[DeviceF-Ten-GigabitEthernet1/0/2] port link-type trunk

[DeviceF-Ten-GigabitEthernet1/0/2] port trunk permit vlan 100 to 200

[DeviceF-Ten-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[DeviceF-Ten-GigabitEthernet1/0/2] link-delay 0 mode updown

[DeviceF-Ten-GigabitEthernet1/0/2] undo stp enable

[DeviceF-Ten-GigabitEthernet1/0/2] quit

(2)     配置RRPP

# 創建RRPP域1。

[DeviceF] rrpp domain 1

# 配置域1的控製VLAN 1000，並將MSTI 1所映射的VLAN配置為該域的保護VLAN。

[DeviceF-rrpp-domain1] control-vlan 1000

[DeviceF-rrpp-domain1] protected-vlan reference-instance 1

# 配置Device F為子環3的主節點，端口Ten-GigabitEthernet1/0/2為主端口，Ten-GigabitEthernet1/0/1為副端口，並使能子環。

[DeviceF-rrpp-domain1] ring 3 node-mode master primary-port ten-gigabitethernet 1/0/2 secondary-port ten-gigabitethernet 1/0/1 level 1

[DeviceF-rrpp-domain1] ring 3 enable

[DeviceF-rrpp-domain1] quit

# 創建RRPP域2。

[DeviceF] rrpp domain 2

# 配置域2的控製VLAN 2000，並將MSTI 2所映射的VLAN配置為該域的保護VLAN。

[DeviceF-rrpp-domain2] control-vlan 2000

[DeviceF-rrpp-domain2] protected-vlan reference-instance 2

# 配置Device F為子環3的主節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能子環。

[DeviceF-rrpp-domain2] ring 3 node-mode master primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 1

[DeviceF-rrpp-domain2] ring 3 enable

[DeviceF-rrpp-domain2] quit

# 全局使能RRPP。

[DeviceF] rrpp enable

6.5.7  Device G的配置

(1)     配置VLAN、MSTP實例和端口

# 創建VLAN 100～VLAN 200。

<DeviceG> system-view

[DeviceG] vlan 100 to 200

# VLAN 100～150映射到MST 1，VLAN 151～200映射到MST 2，並激活MST域的配置。

[DeviceG] stp region-configuration

[DeviceG-mst-region] instance 1 vlan 100 to 150

[DeviceG-mst-region] instance 2 vlan 151 to 200

[DeviceG-mst-region] active region-configuration

[DeviceG-mst-region] quit

# 將端口Ten-GigabitEthernet1/0/1和Ten-GigabitEthernet1/0/2配置為Trunk端口且允許VLAN 100～200通過，不允許VLAN 1通過，分別在端口上配置物理連接狀態up/down抑製時間為0秒（即不抑製），並關閉生成樹協議。

[DeviceG] interface ten-gigabitethernet 1/0/1

[DeviceG-Ten-GigabitEthernet1/0/1] port link-type trunk

[DeviceG-Ten-GigabitEthernet1/0/1] port trunk permit vlan 100 to 200

[DeviceG-Ten-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[DeviceG-Ten-GigabitEthernet1/0/1] link-delay 0 mode updown

[DeviceG-Ten-GigabitEthernet1/0/1] undo stp enable

[DeviceG-Ten-GigabitEthernet1/0/1] quit

[DeviceG] interface ten-gigabitethernet 1/0/2

[DeviceG-Ten-GigabitEthernet1/0/2] port link-type trunk

[DeviceG-Ten-GigabitEthernet1/0/2] port trunk permit vlan 100 to 200

[DeviceG-Ten-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[DeviceG-Ten-GigabitEthernet1/0/2] link-delay 0 mode updown

[DeviceG-Ten-GigabitEthernet1/0/2] undo stp enable

[DeviceG-Ten-GigabitEthernet1/0/2] quit

(2)     配置RRPP

# 創建RRPP域3。

[DeviceG] rrpp domain 3

# 配置域3的控製VLAN 3000，並將MSTI 1所映射的VLAN配置為該域的保護VLAN。

[DeviceG-rrpp-domain3] control-vlan 3000

[DeviceG-rrpp-domain3] protected-vlan reference-instance 1

# 配置Device G為主環傳輸節點，端口Ten-GigabitEthernet1/0/2為主端口，Ten-GigabitEthernet1/0/1為副端口，並使能主環。

[DeviceG-rrpp-domain1] ring 4 node-mode transit primary-port ten-gigabitethernet 1/0/2 secondary-port ten-gigabitethernet 1/0/1 level 0

[DeviceG-rrpp-domain1] ring 4 enable

[DeviceG-rrpp-domain1] quit

# 創建RRPP域4。

[DeviceG] rrpp domain 4

# 配置域4的控製VLAN 4000，並將MSTI 2所映射的VLAN配置為該域的保護VLAN。

[DeviceG-rrpp-domain4] control-vlan 4000

[DeviceG-rrpp-domain4] protected-vlan reference-instance 2

# 配置Device G為主環傳輸節點，端口Ten-GigabitEthernet1/0/2為主端口，Ten-GigabitEthernet1/0/1為副端口，並使能主環。

[DeviceG-rrpp-domain4] ring 4 node-mode transit primary-port ten-gigabitethernet 1/0/2 secondary-port ten-gigabitethernet 1/0/1 level 0

[DeviceG-rrpp-domain4] ring 4 enable

[DeviceG-rrpp-domain4] quit

# 全局使能RRPP。

[DeviceG] rrpp enable

6.5.8  Device H的配置

(1)     配置VLAN、MSTP實例和端口

# 創建VLAN 100～VLAN 200。

<DeviceH> system-view

[DeviceH] vlan 100 to 200

# VLAN 100～150映射到MSTI 1，VLAN 151～200映射到MSTI 2，並激活MST域的配置。

[DeviceH] stp region-configuration

[DeviceH-mst-region] instance 1 vlan 100 to 150

[DeviceH-mst-region] instance 2 vlan 151 to 200

[DeviceH-mst-region] active region-configuration

[DeviceH-mst-region] quit

# 將端口Ten-GigabitEthernet1/0/1和Ten-GigabitEthernet1/0/2配置為Trunk端口且允許VLAN 100～200通過，不允許VLAN 1通過，分別在端口上配置物理連接狀態up/down抑製時間為0秒（即不抑製），並關閉生成樹協議。

[DeviceH] interface ten-gigabitethernet 1/0/1

[DeviceH-Ten-GigabitEthernet1/0/1] port link-type trunk

[DeviceH-Ten-GigabitEthernet1/0/1] port trunk permit vlan 100 to 200

[DeviceH-Ten-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[DeviceH-Ten-GigabitEthernet1/0/1] link-delay 0 mode updown

[DeviceH-Ten-GigabitEthernet1/0/1] undo stp enable

[DeviceH-Ten-GigabitEthernet1/0/1] quit

[DeviceH] interface ten-gigabitethernet 1/0/2

[DeviceH-Ten-GigabitEthernet1/0/2] port link-type trunk

[DeviceH-Ten-GigabitEthernet1/0/2] port trunk permit vlan 100 to 200

[DeviceH-Ten-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[DeviceH-Ten-GigabitEthernet1/0/2] link-delay 0 mode updown

[DeviceH-Ten-GigabitEthernet1/0/2] undo stp enable

[DeviceH-Ten-GigabitEthernet1/0/2] quit

(2)     配置RRPP

# 創建RRPP域3。

[DeviceH] rrpp domain 3

# 配置域3的控製VLAN 3000，並將MSTI 1所映射的VLAN配置為該域的保護VLAN。

[DeviceH-rrpp-domain3] control-vlan 3000

[DeviceH-rrpp-domain3] protected-vlan reference-instance 1

# 配置Device H為主環主節點，端口Ten-GigabitEthernet1/0/1為主端口，Ten-GigabitEthernet1/0/2為副端口，並使能主環。

[DeviceH-rrpp-domain3] ring 4 node-mode master primary-port ten-gigabitethernet 1/0/1 secondary-port ten-gigabitethernet 1/0/2 level 0

[DeviceH-rrpp-domain3] ring 4 enable

[DeviceH-rrpp-domain3] quit

# 創建RRPP域4。

[DeviceH] rrpp domain 4

# 配置域4的控製VLAN 4000，並將MSTI 2所映射的VLAN配置為該域的保護VLAN。

[DeviceH-rrpp-domain4] control-vlan 4000

[DeviceH-rrpp-domain4] protected-vlan reference-instance 2

# 配置Device H為主環主節點，端口Ten-GigabitEthernet1/0/2為主端口，Ten-GigabitEthernet1/0/1為副端口，並使能主環。

[DeviceH-rrpp-domain4] ring 4 node-mode master primary-port ten-gigabitethernet 1/0/2 secondary-port ten-gigabitethernet 1/0/1 level 0

[DeviceH-rrpp-domain4] ring 4 enable

[DeviceH-rrpp-domain4] quit

# 全局使能RRPP。

[DeviceH] rrpp enable

6.6  驗證配置

# 查看Device A的RRPP域1詳細信息。

[DeviceA] display rrpp verbose domain 1

 Domain ID     : 1

 Control VLAN  : Primary 1000, Secondary 1001

 Protected VLAN: Reference instance 1

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Master

Ring State    : Completed

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                   Port status: UP

Secondary port: XGE1/0/2                   Port status: BLOCKED

顯示信息表示Device A在RRPP域1中為主環主節點，且RRPP域1中主環狀態為completed，主端口up，副端口blocked。

# 查看Device A的RRPP域2詳細信息。

[DeviceA] display rrpp verbose domain 2

 Domain ID     : 2

 Control VLAN  : Primary 2000, Secondary 2001

 Protected VLAN: Reference instance 2

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                   Port status: UP

Secondary port: XGE1/0/2                   Port status: UP

顯示信息表示Device A在RRPP域2中為主環傳輸節點，RRPP端口狀態均為up。

# 查看Device B的RRPP域1詳細信息。

[DeviceB] display rrpp verbose domain 1

 Domain ID     : 1

 Control VLAN  : Primary 1000, Secondary 1001

 Protected VLAN: Reference instance 1

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/2                   Port status: UP

Secondary port: XGE1/0/1                   Port status: UP

顯示信息表示Device B在RRPP域1中為主環傳輸節點，RRPP端口狀態均為up。

# 查看Device B的RRPP域2詳細信息。

[DeviceB] display rrpp verbose domain 2

 Domain ID     : 2

 Control VLAN  : Primary 2000, Secondary 2001

 Protected VLAN: Reference instance 2

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Master

Ring State    : Completed

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/2                   Port status: UP

Secondary port: XGE1/0/1                   Port status: BLOCKED

顯示信息表示Device B在RRPP域2中為主環主節點，且RRPP域2中主環狀態為completed，主端口up，副端口blocked。

# 查看Device C的RRPP域1詳細信息。

[DeviceC] display rrpp verbose domain 1

 Domain ID     : 1

 Control VLAN  : Primary 1000, Secondary 1001

 Protected VLAN: Reference instance 1

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                    Port status: UP

Secondary port: XGE1/0/2                    Port status: UP

 

Ring ID       : 2

Ring Level    : 1

Node Mode     : Edge

Ring State    : -

Enable Status : Yes    Active Status: Yes

Common port   : XGE1/0/1                    Port status: UP

                XGE1/0/2                    Port status: UP

Edge port     : XGE1/0/3                    Port status: UP

 

Ring ID       : 3

Ring Level    : 1

Node Mode     : Edge

Ring State    : -

Enable Status : Yes    Active Status: Yes

Common port   : XGE1/0/1                    Port status: UP

                XGE1/0/2                    Port status: UP

Edge port     : XGE1/0/4                    Port status: UP

顯示信息表示Device C在RRPP域1中為主環傳輸節點和子環（Ring 2和Ring 3）邊緣節點，RRPP端口狀態均為up。

# 查看Device C的RRPP域2詳細信息。

[DeviceC] display rrpp verbose domain 2

 Domain ID     : 2

 Control VLAN  : Primary 2000, Secondary 2001

 Protected VLAN: Reference instance 2

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                    Port status: UP

Secondary port: XGE1/0/2                    Port status: UP

 

Ring ID       : 2

Ring Level    : 1

Node Mode     : Edge

Ring State    : -

Enable Status : Yes    Active Status: Yes

Common port   : XGE1/0/1                    Port status: UP

                XGE1/0/2                    Port status: UP

Edge port     : XGE1/0/3                    Port status: UP

 

Ring ID       : 3

Ring Level    : 1

Node Mode     : Edge

Ring State    : -

Enable Status : Yes    Active Status: Yes

Common port   : XGE1/0/1                    Port status: UP

                XGE1/0/2                    Port status: UP

Edge port     : XGE1/0/4                    Port status: UP

顯示信息表示Device C在RRPP域2中為主環傳輸節點和子環（Ring 2和Ring 3）邊緣節點，RRPP端口狀態均為up。

# 查看Device C的邊緣節點和輔助邊緣節點上的環組信息。

[DeviceC] display rrpp ring-group 1

Ring Group 1:

Domain 1 Ring 2 to 3

Domain 2 Ring 2 to 3

# 查看Device D的RRPP域1詳細信息。

[DeviceD] display rrpp verbose domain 1

 Domain ID     : 1

 Control VLAN  : Primary 1000, Secondary 1001

 Protected VLAN: Reference instance 1

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                    Port status: UP

Secondary port: XGE1/0/2                    Port status: UP

 

Ring ID       : 2

Ring Level    : 1

Node Mode     : Assistant-edge

Ring State    : -

Enable Status : Yes    Active Status: Yes

Common port   : XGE1/0/1                    Port status: UP

                XGE1/0/2                    Port status: UP

Edge port     : XGE1/0/3                    Port status: UP

 

Ring ID       : 3

Ring Level    : 1

Node Mode     : Assistant-edge

Ring State    : -

Enable Status : Yes    Active Status: Yes

Common port   : XGE1/0/1                    Port status: UP

                XGE1/0/2                    Port status: UP

Edge port     : XGE1/0/4                    Port status: UP

顯示信息表示Device D在RRPP域1中為主環傳輸節點和子環（Ring 2和Ring 3）輔助邊緣節點，RRPP端口狀態均為up。

# 查看Device D的RRPP域2詳細信息。

[DeviceD] display rrpp verbose domain 2

 Domain ID     : 2

 Control VLAN  : Primary 2000, Secondary 2001

 Protected VLAN: Reference instance 2

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 1

Ring Level    : 0

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                    Port status: UP

Secondary port: XGE1/0/2                    Port status: UP

 

Ring ID       : 2

Ring Level    : 1

Node Mode     : Assistant-edge

Ring State    : -

Enable Status : Yes    Active Status: Yes

Common port   : XGE1/0/1                    Port status: UP

                XGE1/0/2                    Port status: UP

Edge port     : XGE1/0/3                    Port status: UP

 

Ring ID       : 3

Ring Level    : 1

Node Mode     : Assistant-edge

Ring State    : -

Enable Status : Yes    Active Status: Yes

Common port   : XGE1/0/1                    Port status: UP

                XGE1/0/2                    Port status: UP

Edge port     : XGE1/0/4                    Port status: UP

顯示信息表示Device D在RRPP域2中為主環傳輸節點和子環（Ring 2和Ring 3）輔助邊緣節點，RRPP端口狀態均為up。

# 查看Device D的RRPP域3詳細信息。

[DeviceD] display rrpp verbose domain 3

 Domain ID     : 3

 Control VLAN  : Primary 3000, Secondary 3001

 Protected VLAN: Reference instance 1

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 4

Ring Level    : 0

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/5                    Port status: UP

Secondary port: XGE1/0/6                    Port status: UP

顯示信息表示Device D在RRPP域3中為主環傳輸節點，RRPP端口狀態均為up。

# 查看Device D的RRPP域4詳細信息。

[DeviceD] display rrpp verbose domain 4

 Domain ID     : 4

 Control VLAN  : Primary 4000, Secondary 4001

 Protected VLAN: Reference instance 2

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 4

Ring Level    : 0

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/5                    Port status: UP

Secondary port: XGE1/0/6                    Port status: UP

顯示信息表示Device D在RRPP域4中為主環傳輸節點，RRPP端口狀態均為up。

# 查看Device D邊緣節點和輔助邊緣節點上的環組信息。

[DeviceD] display rrpp ring-group 1

Ring Group 1:

Domain 1 Ring 2 to 3

Domain 2 Ring 2 to 3

# 查看Device E的RRPP域1詳細信息。

[DeviceE] display rrpp verbose domain 1

 Domain ID     : 1

 Control VLAN  : Primary 1000, Secondary 1001

 Protected VLAN: Reference instance 1

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 2

Ring Level    : 1

Node Mode     : Master

Ring State    : Completed

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/2                    Port status: UP

Secondary port: XGE1/0/1                    Port status: BLOCKED

顯示信息表示Device E在RRPP域1中為子環（Ring 2）主節點，且RRPP域1中子環狀態為completed，主端口up，副端口blocked。

# 查看Device E的RRPP域2詳細信息。

[DeviceE] display rrpp verbose domain 2

 Domain ID     : 2

 Control VLAN  : Primary 2000, Secondary 2001

 Protected VLAN: Reference instance 2

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 2

Ring Level    : 1

Node Mode     : Master

Ring State    : Completed

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                    Port status: UP

Secondary port: XGE1/0/2                    Port status: BLOCKED

顯示信息表示Device E在RRPP域2中為子環（Ring 2）主節點，且RRPP域2中子環狀態為completed，主端口up，副端口blocked。

# 查看Device F的RRPP域1詳細信息。

[DeviceF] display rrpp verbose domain 1

 Domain ID     : 1

 Control VLAN  : Primary 1000, Secondary 1001

 Protected VLAN: Reference instance 1

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 3

Ring Level    : 1

Node Mode     : Master

Ring State    : Completed

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/2                    Port status: UP

Secondary port: XGE1/0/1                    Port status: BLOCKED

顯示信息表示Device F在RRPP域1中為子環（Ring 3）主節點，且RRPP域1中子環狀態為completed，主端口up，副端口blocked。

# 查看Device F的RRPP域2詳細信息。

[DeviceF] display rrpp verbose domain 2

 Domain ID     : 2

 Control VLAN  : Primary 2000, Secondary 2001

 Protected VLAN: Reference instance 2

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 3

Ring Level    : 1

Node Mode     : Master

Ring State    : Completed

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                    Port status: UP

Secondary port: XGE1/0/2                    Port status: BLOCKED

顯示信息表示Device F在RRPP域2中為子環（Ring 3）主節點，且RRPP域2中子環狀態為completed，主端口up，副端口blocked。

# 查看Device H的RRPP域3詳細信息。

[DeviceH] display rrpp verbose domain 3

 Domain ID     : 3

 Control VLAN  : Primary 3000, Secondary 3001

 Protected VLAN: Reference instance 1

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 4

Ring Level    : 0

Node Mode     : Master

Ring State    : Completed

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/1                    Port status: UP

Secondary port: XGE1/0/2                    Port status: BLOCKED

顯示信息表示Device H在RRPP域3中為主環（Ring 4）主節點，且RRPP域3中主環狀態為completed，主端口up，副端口blocked。

# 查看Device H的RRPP域4詳細信息。

[DeviceH] display rrpp verbose domain 4

 Domain ID     : 4

 Control VLAN  : Primary 4000, Secondary 4001

 Protected VLAN: Reference instance 2

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 4

Ring Level    : 0

Node Mode     : Master

Ring State    : Completed

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/2                    Port status: UP

Secondary port: XGE1/0/1                    Port status: BLOCKED

顯示信息表示Device H在RRPP域4中為主環（Ring 4）主節點，且RRPP域4中主環狀態為completed，主端口up，副端口blocked。

# 查看Device G的RRPP域3詳細信息。

[DeviceG] display rrpp verbose domain 3

 Domain ID     : 3

 Control VLAN  : Primary 3000, Secondary 3001

 Protected VLAN: Reference instance 1

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 4

Ring Level    : 0

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/2                    Port status: UP

Secondary port: XGE1/0/1                    Port status: UP

顯示信息表示Device G在RRPP域3中為主環傳輸節點，RRPP端口狀態均為up。

# 查看Device G的RRPP域4詳細信息。

[DeviceG] display rrpp verbose domain 4

 Domain ID     : 4

 Control VLAN  : Primary 4000, Secondary 4001

 Protected VLAN: Reference instance 2

 Hello timer   : 1 seconds, Fail timer: 3 seconds

 Fast detection status: Disabled

 Fast-Hello timer: 20 ms, Fast-Fail timer: 60 ms

 Fast-Edge-Hello timer: 10 ms, Fast-Edge-Fail timer: 30 ms

 

Ring ID       : 4

Ring Level    : 0

Node Mode     : Transit

Ring State    : -

Enable Status : Yes    Active Status: Yes

Primary port  : XGE1/0/2                    Port status: UP

Secondary port: XGE1/0/1                    Port status: UP

顯示信息表示Device G在RRPP域4中為主環傳輸節點，RRPP端口狀態均為up。

6.7  配置文件

·     Device A：

#

 sysname DeviceA

#

vlan 1

#

vlan 100 to 200

#

stp region-configuration

 instance 1 vlan 100 to 150

 instance 2 vlan 151 to 200

 active region-configuration

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

rrpp domain 1

 control-vlan 1000

 protected-vlan reference-instance 1

 ring 1 node-mode master primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 0

 ring 1 enable

#

rrpp domain 2

 control-vlan 2000

 protected-vlan reference-instance 2

 ring 1 node-mode transit primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 0

 ring 1 enable

#

rrpp enable

#

·     Device B：

#

 sysname DeviceB

#

vlan 1

#

vlan 100 to 200

#

stp region-configuration

 instance 1 vlan 100 to 150

 instance 2 vlan 151 to 200

 active region-configuration

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

rrpp domain 1

 control-vlan 1000

 protected-vlan reference-instance 1

 ring 1 node-mode transit primary-port Ten-GigabitEthernet1/0/2 secondary-port Ten-GigabitEthernet1/0/1 level 0

 ring 1 enable

#

rrpp domain 2

 control-vlan 2000

 protected-vlan reference-instance 2

 ring 1 node-mode master primary-port Ten-GigabitEthernet1/0/2 secondary-port Ten-GigabitEthernet1/0/1 level 0

 ring 1 enable

#

rrpp enable

#

·     Device C：

#

 sysname DeviceC

#

vlan 1

#

vlan 100 to 200

#

stp region-configuration

 instance 1 vlan 100 to 150

 instance 2 vlan 151 to 200

 active region-configuration

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/3

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/4

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

rrpp domain 1

 control-vlan 1000

 protected-vlan reference-instance 1

 ring 1 node-mode transit primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 0

 ring 1 enable

 ring 2 node-mode edge edge-port Ten-GigabitEthernet1/0/3

 ring 2 enable

 ring 3 node-mode edge edge-port Ten-GigabitEthernet1/0/4

 ring 3 enable

#

rrpp domain 2

 control-vlan 2000

 protected-vlan reference-instance 2

 ring 1 node-mode transit primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 0

 ring 1 enable

 ring 2 node-mode edge edge-port Ten-GigabitEthernet1/0/3

 ring 2 enable

 ring 3 node-mode edge edge-port Ten-GigabitEthernet1/0/4

 ring 3 enable

#

rrpp ring-group 1

 domain 1 ring 2 to 3

 domain 2 ring 2 to 3

#

rrpp enable

#

·     Device D：

#

 sysname DeviceD

#

vlan 1

#

vlan 100 to 200

#

stp region-configuration

 instance 1 vlan 100 to 150

 instance 2 vlan 151 to 200

 active region-configuration

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/3

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/4

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/5

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/6

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

rrpp domain 1

 control-vlan 1000

 protected-vlan reference-instance 1

 ring 1 node-mode transit primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 0

 ring 1 enable

 ring 2 node-mode assistant-edge edge-port Ten-GigabitEthernet1/0/3

 ring 2 enable

 ring 3 node-mode assistant-edge edge-port Ten-GigabitEthernet1/0/4

 ring 3 enable

#

rrpp domain 2

 control-vlan 2000

 protected-vlan reference-instance 2

 ring 1 node-mode transit primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 0

 ring 1 enable

 ring 2 node-mode assistant-edge edge-port Ten-GigabitEthernet1/0/3

 ring 2 enable

 ring 3 node-mode assistant-edge edge-port Ten-GigabitEthernet1/0/4

 ring 3 enable

#

rrpp domain 3

 control-vlan 3000

 protected-vlan reference-instance 1

 ring 4 node-mode transit primary-port Ten-GigabitEthernet1/0/5 secondary-port Ten-GigabitEthernet1/0/6 level 0

 ring 4 enable

#

rrpp domain 4

 control-vlan 4000

 protected-vlan reference-instance 2

 ring 4 node-mode transit primary-port Ten-GigabitEthernet1/0/5 secondary-port Ten-GigabitEthernet1/0/6 level 0

 ring 4 enable

#

rrpp ring-group 1

 domain 1 ring 2 to 3

 domain 2 ring 2 to 3

#

rrpp enable

#

·     Device E：

#

 sysname DeviceE

#

vlan 1

#

vlan 100 to 200

#

stp region-configuration

 instance 1 vlan 100 to 150

 instance 2 vlan 151 to 200

 active region-configuration

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

rrpp domain 1

 control-vlan 1000

 protected-vlan reference-instance 1

 ring 2 node-mode master primary-port Ten-GigabitEthernet1/0/2 secondary-port Ten-GigabitEthernet1/0/1 level 1

 ring 2 enable

#

rrpp domain 2

 control-vlan 2000

 protected-vlan reference-instance 2

 ring 2 node-mode master primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 1

 ring 2 enable

#

rrpp enable

#

·     Device F：

#

 sysname DeviceF

#

vlan 1

#

vlan 100 to 200

#

stp region-configuration

 instance 1 vlan 100 to 150

 instance 2 vlan 151 to 200

 active region-configuration

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

rrpp domain 1

 control-vlan 1000

 protected-vlan reference-instance 1

 ring 3 node-mode master primary-port Ten-GigabitEthernet1/0/2 secondary-port Ten-GigabitEthernet1/0/1 level 1

 ring 3 enable

#

rrpp domain 2

 control-vlan 2000

 protected-vlan reference-instance 2

 ring 3 node-mode master primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 1

 ring 3 enable

#

rrpp enable

#

·     Device G：

#

 sysname DeviceG

#

vlan 1

#

vlan 100 to 200

#

stp region-configuration

 instance 1 vlan 100 to 150

 instance 2 vlan 151 to 200

 active region-configuration

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

rrpp domain 3

 control-vlan 3000

 protected-vlan reference-instance 1

 ring 4 node-mode transit primary-port Ten-GigabitEthernet1/0/2 secondary-port Ten-GigabitEthernet1/0/1 level 0

 ring 4 enable

#

rrpp domain 4

 control-vlan 4000

 protected-vlan reference-instance 2

 ring 4 node-mode master primary-port Ten-GigabitEthernet1/0/2 secondary-port Ten-GigabitEthernet1/0/1 level 0

 ring 4 enable

#

rrpp enable

#

·     Device H：

#

 sysname DeviceH

#

vlan 1

#

vlan 100 to 200

#

stp region-configuration

 instance 1 vlan 100 to 150

 instance 2 vlan 151 to 200

 active region-configuration

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 to 200

 link-delay 0 mode updown

 undo stp enable

#

rrpp domain 3

 control-vlan 3000

 protected-vlan reference-instance 1

 ring 4 node-mode master primary-port Ten-GigabitEthernet1/0/1 secondary-port Ten-GigabitEthernet1/0/2 level 0

 ring 4 enable

#

rrpp domain 4

 control-vlan 4000

 protected-vlan reference-instance 2

 ring 4 node-mode master primary-port Ten-GigabitEthernet1/0/2 secondary-port Ten-GigabitEthernet1/0/1 level 0

 ring 4 enable

#

rrpp enable

#

7  相關資料

·     H3C S6890係列以太網交換機 二層技術-以太網交換配置指導（R27xx）

·     H3C S6890係列以太網交換機 二層技術-以太網交換命令參考（R27xx）

·     H3C S6890係列以太網交換機 可靠性配置指導（R27xx）

·     H3C S6890係列以太網交換機 可靠性命令參考（R27xx）