unis f1000-e-l 忘記密碼如何進入bootrom模式

紫光unis f1000-e-l 忘記密碼，ctrl+b和ctrl+c都沒辦法進入，附件是啟動過程，謝各位大佬

NOT Shut down slave cores

PMON2000 MIPS Initializing. Standby...

0xbfe00190  : 000001ef00c8b7b6
CPU CLK SEL : 0000000f
MEM CLK SEL : 0000000f
HT CLK SEL : 00000000
Soft CLK SEL adjust begin
CORE & NODE:04110c85
MEM        :040f017b
fdcoefficient  :0000000f
HT         :01400100
L1_DIV:00000002

DDR_REFC:00000001

BBGEN start  :
BBGEN config value  :fc1de43d
Fix L1xbar illegal access at NODE 0
Fix L2xbar in NODE 0
NO TLB cache init ...
Jump to 9fc
32 bit PCI space translate to 64 bit HT space
set LS7A MISC and confbus base address done.
3A HT in soft freq cfg mode...ok
7A HT in soft freq cfg mode...ok

PLL check success.
Wait HT bus up.01112020>
01112020
Set 7A side HT:
Set width
11110020
Set Freq
82250060
Set soft config
008bc08a
Set Gen3 mode
81237008
Set retry mode
00000081
Enable scrambling
00000078
Set CPU side HT:
Set width
11112020
Set Freq
02258923
Set soft config
008b908a
Set GEN3 mode
88600000
Set retry mode
00000081
Enable scrambling
00000078
Reset Node 0 HT1 bus
00600000
Wait HT bus down.>
11112010
Dereset Node 0 HT1 bus
00200000
Wait HT bus up.>
11112020

After reconnect, PLL check success.
Checking Node 0 HT1 CRC error.>
Checking Bridge HT CRC error bit.>
LS3A-7A linkup.
Start Init Memory, wait a while......
NODE 0 MEMORY CONFIG BEGIN


s1 = 0xc1a10400__c1a10400
Disable cpu buffered read
Disable read buffer

Enable register space of MEMORY
run to wait dram init ok!3

Disable register space of MEMORY

Disable register space of MEMORY done.
Start Hard Leveling...

Enable register space of MEMORY

write leveling begin

all dll_wrdqs set 0

set leveling mode to be WRITE LEVELING

write leveling ready
00000001000000020000000200000003000000030000000400000004000000050000000500000006000000060000000700000007000000080000000800000008
write leveling finish and gate leveling begin

PREAMBLE CHECK!!

The preamble check not found @00000055training again ...

PREAMBLE CHECK!!

The preamble check success

PREAMBLE CHECK!!

The preamble check not found @00000055training again ...

PREAMBLE CHECK!!

The preamble check success

PREAMBLE CHECK!!

The preamble check not found @00000055training again ...

PREAMBLE CHECK!!

The preamble check success

PREAMBLE CHECK!!

The preamble check not found @00000055training again ...

PREAMBLE CHECK!!

The preamble check success

PREAMBLE CHECK!!

The preamble check not found @00000055training again ...

PREAMBLE CHECK!!

The preamble check success

PREAMBLE CHECK!!

The preamble check not found @00000055training again ...

PREAMBLE CHECK!!

The preamble check success

PREAMBLE CHECK!!

The preamble check not found @00000055training again ...

PREAMBLE CHECK!!

The preamble check success

PREAMBLE CHECK!!

The preamble check not found @00000055training again ...

PREAMBLE CHECK!!

The preamble check success

MC0 Config DONE

Enable register space of MEMORY
run to wait dram init ok!3

Disable register space of MEMORY

Disable register space of MEMORY done.
Start Hard Leveling...

Enable register space of MEMORY

write leveling begin

all dll_wrdqs set 0

set leveling mode to be WRITE LEVELING

write leveling ready
00000001000000020000000200000003000000030000000400000004000000050000000500000006000000060000000700000007000000080000000800000008
write leveling finish and gate leveling begin

PREAMBLE CHECK!!

The preamble check not found @00000055training again ...

PREAMBLE CHECK!!

The preamble check success

PREAMBLE CHECK!!

The preamble check not found @00000055training again ...

PREAMBLE CHECK!!

The preamble check success

PREAMBLE CHECK!!

The preamble check not found @00000055training again ...

PREAMBLE CHECK!!

The preamble check success

PREAMBLE CHECK!!

The preamble check not found @00000055training again ...

PREAMBLE CHECK!!

The preamble check success

PREAMBLE CHECK!!

The preamble check not found @00000055training again ...

PREAMBLE CHECK!!

The preamble check success

PREAMBLE CHECK!!

The preamble check not found @00000055training again ...

PREAMBLE CHECK!!

The preamble check success

PREAMBLE CHECK!!

The preamble check success

PREAMBLE CHECK!!

The preamble check not found @00000055training again ...

PREAMBLE CHECK!!

The preamble check success

MC1 Config DONE
DDR Interleave space open : 0x00000000 - 0x0FFFFFFF
PCI space open: 0x80000000 - 0x8FFFFFFF
MC0/1 space open : 0x80000000 - 0x17FFFFFFF
Full PCI space opened as cpu.

msize = 0x00000008
The uncache data is:
00000000:  5555555555555555
00000008:  aaaaaaaaaaaaaaaa
00000010:  3333333333333333
00000018:  cccccccccccccccc
00000020:  7777777777777777
00000028:  8888888888888888
00000030:  1111111111111111
00000038:  eeeeeeeeeeeeeeee
The cached  data is:
00000000:  5555555555555555
00000008:  aaaaaaaaaaaaaaaa
00000010:  3333333333333333
00000018:  cccccccccccccccc
00000020:  7777777777777777
00000028:  8888888888888888
00000030:  1111111111111111
00000038:  eeeeeeeeeeeeeeee
Init Memory done.

NODE ID:00000000    CORE ID:00000000
Lock Scache Node x--9800?00?00000000~4K...
Lock Scache Done.

Start Testing Memory...

Address Stuck Testing all space...
Test address range: 0x9800000080100000~0x9800000088000000
write done...
Stuck Testing done!

Pattern WalkOnes Test...
Test address range: 0x9800000080100000~0x9800000088000000  @@  address interval: 0x00000040
write done. begin to read and compare...
Pattern Testing done.

Pattern WalkInvOnes Test...
Test address range: 0x9800000080100000~0x9800000088000000  @@  address interval: 0x00000040
write done. begin to read and compare...
Pattern Testing done.

Pattern WalkZeros Test...
Test address range: 0x9800000080100000~0x9800000088000000  @@  address interval: 0x00000040
write done. begin to read and compare...
Pattern Testing done.

Pattern WalkSingleOnes Test...
Test address range: 0x9800000080100000~0x9800000088000000  @@  address interval: 0x00000040
write done. begin to read and compare...
Pattern Testing done.

Unlock Scache Node x--9800?00000000000~4K...
Unlock Scache Done.

0000000000000000
bridge CHIP ID: 0x7a810040revision: 0x00000000
Open 3A HT RX space.
Disable 3A HT dw_write.
Open 7A HT RX space.
Disable 7A HT dw_write.
Enable 7A HT configure access.
Node 0 LS3A-7A init done.
Read local memory..
Read node0 7A times: 0x10000 ..
config 7A dma route done.
7A HT Hi clock disabled.
LS7A pll configure done.
LS7A chip init done.
PCIE enabled
SATA0 enabled
SATA1 enabled
SATA2 enabled
USB0 enabled
USB1 enabled
unused PCIE F0 ports clock disabled.
Powerdown PCIE F1 PHY and disable all Ports.
unused PCIE F1 ports clock disabled.
Powerdown PCIE H PHY and disable all Ports.
unused PCIE H ports clock disabled.
Powerdown PCIE G0 PHY and disable all Ports.
unused PCIE G0 ports clock disabled.
unused PCIE G1 ports clock disabled.
Gmem config begin
Enable gmem config space

write leveling begin

all dll_wrdqs set 0

set leveling mode to be WRITE LEVELING

write leveling ready
00000001000000020000000200000002
write leveling finish and gate leveling begin

PREAMBLE CHECK!!

The preamble check not found @00000055training again ...

PREAMBLE CHECK!!

The preamble check success

PREAMBLE CHECK!!

The preamble check not found @00000055training again ...

PREAMBLE CHECK!!

The preamble check success
Disable gmem config space
The gmem data is:
00000000:  5555555555555555
00000008:  aaaaaaaaaaaaaaaa
00000010:  3333333333333333
00000018:  cccccccccccccccc
00000020:  7777777777777777
00000028:  8888888888888888
00000030:  1111111111111111
00000038:  eeeeeeeeeeeeeeee
LS7A uncache accellerator enabled

LS7A init done.
Copy PMON to execute location...
  start = 0x8f900000
  s0 = 0x30300000
  _edata = 0x8f9ad010
  _end = 0x8f9ae028copy text section done.
Copy PMON to execute location done.
NOT Wake up other cores
sp=8f8fc000
Uncompressing Bios................................................................................OK,Booting Bios
memorysize_high: 0xf0000000
FREQ
FREI
cpu freq 1187900000
DONE
DEVI
ENVI
MAPV
in envinit
nvram=bfc00000
NVRAM@bfcff000
STDV
80100000:  memory between 8f7ff400-8f800000  is already been allocated,heap is already above this point
SBDD
P12PCIH
PCIH
PCID
pcie-slot device: vendor:8086 product:1522
PCIS
PCIR
PCIW
NETI
RTCL
PCID
can't find xhci
begin dc_init
enter dc_init...
frame buffer addr: 42000000
for pixclock = 38220 khz, found: pstdiv = 45, loopc = 86, refc = 5, precision = 1 / 10000.
for pixclock = 38220 khz, found: pstdiv = 45, loopc = 86, refc = 5, precision = 1 / 10000.
display controller reg config complete!
fbaddress = c2000000
cfb_console init,fb=c2000000
CONSOLE_SIZE 960000
fb_init done
vga available : 1
in configure
mainbus0 (root)
localbus0 at mainbus0
pcibr0 at mainbus0
pci0 at pcibr0 bus 0
syn0 at pci0 dev 3 function 0 vendor/product: 0x0014/0x7a03 (network, ethernet)membasep=0x49298000
using ls7a spi mode set mac
syn0 Mac address: 2a:57:25:68:0a:7b
MAC:0x2a    0x57    0x25    0x68    0xa    0x7b    Now Going to Call register_netdev to             register the network interface for GMAC core
DATA after Reset = 00020100

Now Registering the netdevice
in if attach
syn1 at pci0 dev 3 function 1 vendor/product: 0x0014/0x7a03 (network, ethernet)membasep=0x49290000
using ls7a spi mode set mac
syn1 Mac address: 86:bf:4f:47:e6:9b
MAC:0x86    0xbf    0x4f    0x47    0xe6    0x9b    Now Going to Call register_netdev to             register the network interface for GMAC core
DATA after Reset = 00020100

Now Registering the netdevice
in if attach
ohci0 at pci0 dev 4 function 0 vendor/product: 0x0014/0x7a24 (serialbus, USB)usb base addr : 0xc9288000, bus_base is : 0xc0000000
OHCI revision: 0x00000110
  RH: a: 0x02000903 b: 0x00000000
early period(0x0)
OHCI 8b01ec00 initialized ok
drive at ohci0 devnum 1, Product OHCI Root Hub
 not configured
vendor/product: 0x0014/0x7a14 (serialbus, USB) at pci0 dev 4 function 1 not configured
ohci1 at pci0 dev 5 function 0 vendor/product: 0x0014/0x7a24 (serialbus, USB)usb base addr : 0xc9278000, bus_base is : 0xc0000000
OHCI revision: 0x00000110
  RH: a: 0x02000903 b: 0x00000000
early period(0x0)
OHCI 8b01e800 initialized ok
drive at ohci1 devnum 2, Product OHCI Root Hub
 not configured
vendor/product: 0x0014/0x7a14 (serialbus, USB) at pci0 dev 5 function 1 not configured
vendor/product: 0x0014/0x7a15 (multimedia, video) at pci0 dev 6 function 0 not configured
vendor/product: 0x0014/0x7a06 (display, miscellaneous) at pci0 dev 6 function 1 not configured
vendor/product: 0x0014/0x7a07 (multimedia, subclass: 0x03) at pci0 dev 7 function 0 not configured
ahci0 at pci0 dev 8 function 0 vendor/product: 0x0014/0x7a08 (mass storage, subclass: 0x06)Found memory space: memt->bus_base=0xc0000000, baseaddr=0x492a4000size=0x2000
ahci_init_one:426: regbase = c92a4000
Global controller reset.
PORT_SCR_ERR 0x0
PORT_IRQ_STAT 0x0
Port 0 status: 0x0
HOST_CTL 0x80000000
HOST_CTL 0x80000002
AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: 64bit ncq stag pm led clo only pmp pio slum part
ahci: linkmap=0
ahci1 at pci0 dev 8 function 1 vendor/product: 0x0014/0x7a08 (mass storage, subclass: 0x06)Found memory space: memt->bus_base=0xc0000000, baseaddr=0x492a2000size=0x2000
ahci_init_one:426: regbase = c92a2000
Global controller reset.
PORT_SCR_ERR 0x4050002
PORT_IRQ_STAT 0x0
Port 0 status: 0x123
HOST_CTL 0x80000000
HOST_CTL 0x80000002
AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: 64bit ncq stag pm led clo only pmp pio slum part
ahci: linkmap=1
wd0 at ahci1cmd_slot = 0x8b026800
cmd_tbl_dma = 0x8b026a00
cxk debug
Exit start port 0
ahci2 at pci0 dev 8 function 2 vendor/product: 0x0014/0x7a08 (mass storage, subclass: 0x06)Found memory space: memt->bus_base=0xc0000000, baseaddr=0x492a0000size=0x2000
ahci_init_one:426: regbase = c92a0000
Global controller reset.
PORT_SCR_ERR 0x0
PORT_IRQ_STAT 0x0
Port 0 status: 0x0
HOST_CTL 0x80000000
HOST_CTL 0x80000002
AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: 64bit ncq stag pm led clo only pmp pio slum part
ahci: linkmap=0
ppb0 at pci0 dev 9 function 0 vendor/product: 0x0014/0x7a19 (bridge, PCI)
pci1 at ppb0 bus 1
igb0 at pci1 dev 0 function 0 vendor/product: 0x8086/0x1521 (network, ethernet)Invalid MAC Address
Invalid MAC Address
Intel(R) Gigabit Ethernet Network Connection
: (PCIe:5.0GT/s:Width x4) MAC: 0x8b01e5f8M
: PBA No: 106300-000
Using legacy interrupts. 1 rx queue(s), 1 tx queue(s)
: (null), address dc:2d:cb:16:e6:c6
in if attach
igb1 at pci1 dev 0 function 1 vendor/product: 0x8086/0x1521 (network, ethernet)Invalid MAC Address
Invalid MAC Address
Intel(R) Gigabit Ethernet Network Connection
: (PCIe:5.0GT/s:Width x4) MAC: 0x8b01e1f8M
: PBA No: 106300-000
Using legacy interrupts. 1 rx queue(s), 1 tx queue(s)
: (null), address dc:2d:cb:16:e6:c7
in if attach
igb2 at pci1 dev 0 function 2 vendor/product: 0x8086/0x1521 (network, ethernet)Invalid MAC Address
Invalid MAC Address
Intel(R) Gigabit Ethernet Network Connection
: (PCIe:5.0GT/s:Width x4) MAC: 0x8b02cdf8M
: PBA No: 106300-000
Using legacy interrupts. 1 rx queue(s), 1 tx queue(s)
: (null), address dc:2d:cb:16:e6:c8
in if attach
igb3 at pci1 dev 0 function 3 vendor/product: 0x8086/0x1521 (network, ethernet)Invalid MAC Address
Invalid MAC Address
Intel(R) Gigabit Ethernet Network Connection
: (PCIe:5.0GT/s:Width x4) MAC: 0x8b02c9f8M
: PBA No: 106300-000
Using legacy interrupts. 1 rx queue(s), 1 tx queue(s)
: (null), address dc:2d:cb:16:e6:c9
in if attach
ppb1 at pci0 dev 17 function 0 vendor/product: 0x0014/0x7a29 (bridge, PCI)
pci2 at ppb1 bus 2
igb4 at pci2 dev 0 function 0 vendor/product: 0x8086/0x1522 (network, ethernet)Invalid MAC Address
Invalid MAC Address
Intel(R) Gigabit Ethernet Network Connection
: (PCIe:5.0GT/s:Width x4) MAC: 0x8b02c5f8M
: PBA No: 106300-000
Using legacy interrupts. 1 rx queue(s), 1 tx queue(s)
: (null), address dc:2d:cb:16:e6:ca
in if attach
igb5 at pci2 dev 0 function 1 vendor/product: 0x8086/0x1522 (network, ethernet)Invalid MAC Address
Invalid MAC Address
Intel(R) Gigabit Ethernet Network Connection
: (PCIe:5.0GT/s:Width x4) MAC: 0x8b02c1f8M
: PBA No: 106300-000
Using legacy interrupts. 1 rx queue(s), 1 tx queue(s)
: (null), address dc:2d:cb:16:e6:cb
in if attach
igb6 at pci2 dev 0 function 2 vendor/product: 0x8086/0x1522 (network, ethernet)Invalid MAC Address
Invalid MAC Address
Intel(R) Gigabit Ethernet Network Connection
: (PCIe:5.0GT/s:Width x4) MAC: 0x8b035df8M
: PBA No: 106300-000
Using legacy interrupts. 1 rx queue(s), 1 tx queue(s)
: (null), address dc:2d:cb:16:e6:cc
in if attach
igb7 at pci2 dev 0 function 3 vendor/product: 0x8086/0x1522 (network, ethernet)Invalid MAC Address
Invalid MAC Address
Intel(R) Gigabit Ethernet Network Connection
: (PCIe:5.0GT/s:Width x4) MAC: 0x8b0359f8M
: PBA No: 106300-000
Using legacy interrupts. 1 rx queue(s), 1 tx queue(s)
: (null), address dc:2d:cb:16:e6:cd
in if attach
vendor/product: 0x0014/0x7a0b (system, miscellaneous) at pci0 dev 22 function 0 not configured
out configure
Press <Del> to set BIOS,waiting for 3 seconds here.....
devconfig done.
ifinit done.
domaininit done.
init_proc....
HSTI
SYMI
SBDE

[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[
[[  [[[[[[[[[       [[[[[       [[[[   [[[[[  [[[[[      [[[[[       [[[[[       [[[[   [[[[[  [[
[[  [[[[[[[[   [[[[  [[[   [[[[  [[[    [[[[  [[[[  [[[[  [[[   [[[[  [[[   [[[[  [[[    [[[[  [[
[[  [[[[[[[[  [[[[[[ [[[  [[[[[[ [[[  [  [[[  [[[  [[[[[[[[[[[[   [[[[[[[  [[[[[[ [[[  [  [[[  [[
[[  [[[[[[[[  [[[[[[ [[[  [[[[[[ [[[  [[  [[  [[[  [[[    [[[[[[[    [[[[  [[[[[[ [[[  [[  [[  [[
[[  [[[[[[[[  [[[[[[ [[[  [[[[[[ [[[  [[[  [  [[[  [[[[[  [[[[[[[[[[  [[[  [[[[[[ [[[  [[[  [  [[
[[  [[[[[[[[   [[[[  [[[   [[[[  [[[  [[[[    [[[   [[[[  [[[   [[[  [[[[   [[[[  [[[  [[[[    [[
[[       [[[[       [[[[[       [[[[  [[[[[   [[[[       [[[[[      [[[[[[       [[[[  [[[[[   [[
[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[2011 Loongson][[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[

Configuration [Bonito,EL,NET,SCSI,IDE]
Version: PMON2000 3.3 (Bonito) #38: Sat Jan 19 16:01:51 CST 2019 commit 7a58e3840f01ce3791389027283ed7adaab2ebb8 Author: SunChengLian <sunchenglian@***.***> Date:   Mon Dec 17 16:59:49 2018 +0800 .
Supported loaders [txt, srec, elf, bin]
Supported filesystems [net, fat, fs, disk, iso9660, socket, tty, ram]
This software may be redistributed under the BSD copyright.
Copyright 2000-2002, Opsycon AB, Sweden.
Copyright 2005, ICT CAS.
CPU GODSON3 BogoMIPS: 2368
sw selected! mem@ 495Mhz
Memory size 4096 MB .
Primary Instruction cache size 64kb (64 line, 4 way)
Primary Data cache size 64kb (64 line, 4 way)
Secondary cache size 4096kb
                                                                                                                                                                                                                                                                             |BEV1
BEV0
BEV in SR set to zero.
working_fdt=0xbfcfb004
dtb verify ok!!!                                                                                                                                                                                                                                                             /Not find the file or directory!
we can't locate root directory in super block!                                                                                                                                                                                                                               |Now booting the SPOS(SPOS)                                                                                                                                                                                                                                                   /Loading file: (wd0,1)/vmlinux.64 (elf)
(elf)                                                                                                                                                                                                                                                                        -0x80200000/30459712 + 0x81f0c740/35043200(z) + 20481 syms-
Entry address is 80888fe0
Boot with parameters: cached cOnsole=tty cOnsole=ttyS0,115200 rdinit=/sbin/init waitdev=sda2
/home/tarena/loongson/abt/pmon-loongson3/Targets/Bonito3a3000_7a/compile/Bonito/../../../../pmon/common/env.c:length of boot_param is 00000098
ac = 00000007, nsp @ 8f00fea0, env @ ffffffff, en @ 8f00ff28
vsp = 08xffffffff8f00fec0, ssp @ 08xffffffff8f00ff28
memory_offset = 0x286dd8;cpu_offset = 0x2879e4; system_offset = 0x287a40; irq_offset = 0x289db4; interface_offset = 0x289e08;
board_name:Loongson-3A3000-7A-Dev-1way ---0x8f299da0 10
Shutdown:0x20006963 reset:0x8f0711f0
Update bootarg error
   zero      at       v0       v1       a0       a1       a2       a3   
 00000000 00000000 00000000 00000000 00000007 8f00fea0 8f00ff28 8f166660
    t0       t1       t2       t3       t4       t5       t6       t7   
 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
    s0       s1       s2       s3       s4       s5       s6       s7   
 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
    t8       t9       k0       k1       gp       sp       s8       ra   
 00000000 00000000 00000000 00000000 00000000 8f00fe80 00000000 8f0ab818
set coherent
SET HT_DMA CACHED
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.10.0+ (bian@complite-server) (gcc version 4.9.3 20150626 (Red Hat 4.9.3-2) (GCC) ) #22 SMP PREEMPT Fri Sep 24 17:57:19 CST 2021
[    0.000000] Boot CPU ID is being fixed from 0 to 0
[    0.000000] Shutdown Addr: ffffffff8f0711f0 Reset Addr: ffffffff8f071210
[    0.000000] CpuClock = 1187900000
[    0.000000] CP0_Config3: CP0 16.3 (0xffffffff80803ca0)
[    0.000000] CP0_PageGrain: CP0 5.1 (0x68000000)
[    0.000000] NUMA: Discovered 4 cpus on 1 nodes
[    0.000000] Debug: node_id:0, mem_type:1, mem_start:0x200000, mem_size:0x8e MB
[    0.000000]        start_pfn:0x200, end_pfn:0x9000, num_physpages:0x8e00
[    0.000000] Debug: node_id:0, mem_type:2, mem_start:0x90000000, mem_size:0xf00 MB
[    0.000000]        start_pfn:0x90000, end_pfn:0x180000, num_physpages:0xf8e00
[    0.000000] node0's addrspace_offset is 0x0
[    0.000000] Node0's start_pfn is 0x200, end_pfn is 0x180000, freepfn is 0x4078
[    0.000000] NUMA: set cpumask cpu 0 on node 0
[    0.000000] NUMA: set cpumask cpu 1 on node 0
[    0.000000] NUMA: set cpumask cpu 2 on node 0
[    0.000000] NUMA: set cpumask cpu 3 on node 0
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0014630d (ICT Loongson-3)
[    0.000000] FPU revision is: 00770501
[    0.000000] Checking for the multiply/shift bug... no.
[    0.000000] Checking for the daddiu bug... no.
[    0.000000] MIPS: machine is loongson,generic
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 0000000008e00000 @ 0000000000200000 (usable)
[    0.000000]  memory: 0000000000002000 @ 000000000fffe000 (reserved)
[    0.000000]  memory: 00000000f0000000 @ 0000000090000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] software IO TLB [mem 0x048b0000-0x088b0000] (64MB) mapped at [98000000048b0000-98000000088affff]
[    0.000000] Zone ranges:
[    0.000000]   DMA32    [mem 0x00200000-0xffffffff]
[    0.000000]   Normal   [mem 0x100000000-0x17fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00200000-0x08ffffff]
[    0.000000]   node   0: [mem 0x90000000-0x17fffffff]
[    0.000000] Detected 4 available CPU(s)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 64 bytes.
[    0.000000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
[    0.000000] Unified victim cache 256kB 16-way, linesize 64 bytes.
[    0.000000] Unified secondary cache 8192kB 16-way, linesize 64 bytes.
[    0.000000] PERCPU: Embedded 14 pages/cpu @980000000893f000 s18240 r8192 d30912 u57344
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 1003464
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: cached cOnsole=tty cOnsole=ttyS0,115200 rdinit=/sbin/init waitdev=sda2 ethaddr=dc:2d:cb:16:e6:c6
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] total ram pages initialed 0
[    0.000000] total ram pages are 962223
[    0.000000] Memory: 3848888k/4077568k available (6737k kernel code, 228680k reserved, 2538k data, 20484k init, 0k highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]     Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000]     RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4.
[    0.000000] NR_IRQS:352
[    0.000000] Supports HT MSI interrupt, enabling LS7A MSI Interrupt.
[    0.000000] set clock event to periodic mode!
[    0.000000] hpet clock event device register
[    0.000000] Console: colour dummy device 80x25
[    0.003906] console [tty0] enabled
[    0.007812] allocated 16777216 bytes of page_cgroup
[    0.011718] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.015625] Calibrating delay loop... 2374.35 BogoMIPS (lpj=4636672)
[    0.050781] pid_max: default: 32768 minimum: 301
[    0.054687] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.058593] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.062500] Mount-cache hash table entries: 4096
[    0.066406] Initializing cgroup subsys memory
[    0.070312] Initializing cgroup subsys blkio
[    0.074218] Checking for the daddi bug... no.
[    0.078125] Performance counters: mips/loongson3 PMU enabled, 4 48-bit counters available to each CPU, irq -1 (share with timer interrupt)
[    0.093750] Enable clock for CPU#1
[    0.093750] Booting CPU#1...
[    0.097656] Primary instruction cache 64kB, VIPT, 4-way, linesize 64 bytes.
[    0.097656] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
[    0.097656] Unified victim cache 256kB 16-way, linesize 64 bytes.
[    0.097656] Unified secondary cache 8192kB 16-way, linesize 64 bytes.
[    0.101562] CPU revision is: 0014630d (ICT Loongson-3)
[    0.101562] FPU revision is: 00770501
[    0.117187] CPU#1 finished, CP0_ST=d400cce1
[    0.121093] Enable clock for CPU#2
[    0.121093] Booting CPU#2...
[    0.121093] Primary instruction cache 64kB, VIPT, 4-way, linesize 64 bytes.
[    0.121093] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
[    0.121093] Unified victim cache 256kB 16-way, linesize 64 bytes.
[    0.121093] Unified secondary cache 8192kB 16-way, linesize 64 bytes.
[    0.125000] CPU revision is: 0014630d (ICT Loongson-3)
[    0.125000] FPU revision is: 00770501
[    0.140625] CPU#2 finished, CP0_ST=d400cce1
[    0.144531] Enable clock for CPU#3
[    0.144531] Booting CPU#3...
[    0.144531] Primary instruction cache 64kB, VIPT, 4-way, linesize 64 bytes.
[    0.144531] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
[    0.144531] Unified victim cache 256kB 16-way, linesize 64 bytes.
[    0.144531] Unified secondary cache 8192kB 16-way, linesize 64 bytes.
[    0.148437] CPU revision is: 0014630d (ICT Loongson-3)
[    0.148437] FPU revision is: 00770501
[    0.164062] CPU#3 finished, CP0_ST=d400cce1
[    0.164062] Brought up 4 CPUs
[    0.164062] devtmpfs: initialized
[    0.164062] NET: Registered protocol family 16
[    0.167968] node counter clock source device register
[    0.171875] Can't analyze schedule() prologue at ffffffff8088f580
[    0.195312] SCSI subsystem initialized
[    0.195312] usbcore: registered new interface driver usbfs
[    0.195312] usbcore: registered new interface driver hub
[    0.195312] usbcore: registered new device driver usb
[    0.195312] pps_core: LinuxPPS API ver. 1 registered
[    0.195312] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.195312] PTP clock support registered
[    0.195312] PCI host bridge to bus 0000:00
[    0.195312] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[    0.195312] pci_bus 0000:00: root bus resource [io  0x4000-0xffff]
[    0.195312] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.195312] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.203125] pci 0000:00:06.0: BAR 2: assigned [mem 0x40000000-0x47ffffff 64bit]
[    0.203125] pci 0000:00:16.0: BAR 2: assigned [mem 0x48000000-0x48ffffff 64bit]
[    0.203125] pci 0000:00:09.0: BAR 8: assigned [mem 0x49000000-0x490fffff]
[    0.203125] pci 0000:00:11.0: BAR 8: assigned [mem 0x49100000-0x491fffff]
[    0.203125] pci 0000:00:06.0: BAR 0: assigned [mem 0x49200000-0x4923ffff 64bit]
[    0.203125] pci 0000:00:06.1: BAR 0: assigned [mem 0x49240000-0x4924ffff 64bit]
[    0.203125] pci 0000:00:07.0: BAR 0: assigned [mem 0x49250000-0x4925ffff 64bit]
[    0.203125] pci 0000:00:03.0: BAR 0: assigned [mem 0x49260000-0x49267fff 64bit]
[    0.203125] pci 0000:00:03.1: BAR 0: assigned [mem 0x49268000-0x4926ffff 64bit]
[    0.203125] pci 0000:00:04.0: BAR 0: assigned [mem 0x49270000-0x49277fff 64bit]
[    0.203125] pci 0000:00:04.1: BAR 0: assigned [mem 0x49278000-0x4927ffff 64bit]
[    0.203125] pci 0000:00:05.0: BAR 0: assigned [mem 0x49280000-0x49287fff 64bit]
[    0.203125] pci 0000:00:05.1: BAR 0: assigned [mem 0x49288000-0x4928ffff 64bit]
[    0.203125] pci 0000:00:08.0: BAR 0: assigned [mem 0x49290000-0x49291fff 64bit]
[    0.203125] pci 0000:00:08.1: BAR 0: assigned [mem 0x49292000-0x49293fff 64bit]
[    0.203125] pci 0000:00:08.2: BAR 0: assigned [mem 0x49294000-0x49295fff 64bit]
[    0.203125] pci 0000:00:09.0: BAR 0: assigned [mem 0x49296000-0x49296fff 64bit]
[    0.203125] pci 0000:00:09.0: BAR 7: assigned [io  0x4000-0x4fff]
[    0.203125] pci 0000:00:11.0: BAR 0: assigned [mem 0x49297000-0x49297fff 64bit]
[    0.203125] pci 0000:00:11.0: BAR 7: assigned [io  0x5000-0x5fff]
[    0.203125] pci 0000:00:16.0: BAR 0: assigned [mem 0x49298000-0x49298fff 64bit]
[    0.203125] pci 0000:01:00.0: BAR 0: assigned [mem 0x49000000-0x4901ffff]
[    0.203125] pci 0000:01:00.1: BAR 0: assigned [mem 0x49020000-0x4903ffff]
[    0.203125] pci 0000:01:00.2: BAR 0: assigned [mem 0x49040000-0x4905ffff]
[    0.203125] pci 0000:01:00.3: BAR 0: assigned [mem 0x49060000-0x4907ffff]
[    0.203125] pci 0000:01:00.0: BAR 3: assigned [mem 0x49080000-0x49083fff]
[    0.203125] pci 0000:01:00.1: BAR 3: assigned [mem 0x49084000-0x49087fff]
[    0.203125] pci 0000:01:00.2: BAR 3: assigned [mem 0x49088000-0x4908bfff]
[    0.203125] pci 0000:01:00.3: BAR 3: assigned [mem 0x4908c000-0x4908ffff]
[    0.203125] pci 0000:01:00.0: BAR 2: assigned [io  0x4000-0x401f]
[    0.203125] pci 0000:01:00.1: BAR 2: assigned [io  0x4020-0x403f]
[    0.203125] pci 0000:01:00.2: BAR 2: assigned [io  0x4040-0x405f]
[    0.203125] pci 0000:01:00.3: BAR 2: assigned [io  0x4060-0x407f]
[    0.203125] pci 0000:00:09.0: PCI bridge to [bus 01]
[    0.203125] pci 0000:00:09.0:   bridge window [io  0x4000-0x4fff]
[    0.203125] pci 0000:00:09.0:   bridge window [mem 0x49000000-0x490fffff]
[    0.203125] pci 0000:02:00.0: BAR 0: assigned [mem 0x49100000-0x4911ffff]
[    0.203125] pci 0000:02:00.1: BAR 0: assigned [mem 0x49120000-0x4913ffff]
[    0.203125] pci 0000:02:00.2: BAR 0: assigned [mem 0x49140000-0x4915ffff]
[    0.203125] pci 0000:02:00.3: BAR 0: assigned [mem 0x49160000-0x4917ffff]
[    0.203125] pci 0000:02:00.0: BAR 3: assigned [mem 0x49180000-0x49183fff]
[    0.203125] pci 0000:02:00.1: BAR 3: assigned [mem 0x49184000-0x49187fff]
[    0.203125] pci 0000:02:00.2: BAR 3: assigned [mem 0x49188000-0x4918bfff]
[    0.203125] pci 0000:02:00.3: BAR 3: assigned [mem 0x4918c000-0x4918ffff]
[    0.203125] pci 0000:02:00.0: BAR 2: assigned [io  0x5000-0x501f]
[    0.203125] pci 0000:02:00.1: BAR 2: assigned [io  0x5020-0x503f]
[    0.203125] pci 0000:02:00.2: BAR 2: assigned [io  0x5040-0x505f]
[    0.203125] pci 0000:02:00.3: BAR 2: assigned [io  0x5060-0x507f]
[    0.203125] pci 0000:00:11.0: PCI bridge to [bus 02]
[    0.203125] pci 0000:00:11.0:   bridge window [io  0x5000-0x5fff]
[    0.203125] pci 0000:00:11.0:   bridge window [mem 0x49100000-0x491fffff]
[    0.203125] ls-spi ls-spi.0: master is unqueued, this is deprecated
[    0.687500] Switched to clocksource node_counter
[    0.699218] NET: Registered protocol family 2
[    0.703125] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.710937] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.718750] TCP: Hash tables configured (established 32768 bind 32768)
[    0.726562] TCP: reno registered
[    0.726562] UDP hash table entries: 2048 (order: 5, 131072 bytes)
[    0.734375] UDP-Lite hash table entries: 2048 (order: 5, 131072 bytes)
[    0.742187] NET: Registered protocol family 1
[    0.746093] PCI: Enabling device 0000:00:04.0 (0040 -> 0042)
[    0.804687] pci 0000:00:04.1: EHCI: unrecognized capability 00
[    0.808593] PCI: Enabling device 0000:00:05.0 (0040 -> 0042)
[    0.867187] pci 0000:00:05.1: EHCI: unrecognized capability 00
[    1.804687] i2c-gpio platform:i2c-gpio@0: using pins 73 (SDA) and 74 (SCL)
[    1.812500] i2c-gpio platform:i2c-gpio@1: using pins 75 (SDA) and 76 (SCL)
[    1.820312] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    1.828125] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.835937] VFS: Disk quotas dquot_6.5.2
[    1.839843] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.847656] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.855468] msgmni has been set to 7517
[    1.859375] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    1.867187] io scheduler noop registered
[    1.871093] io scheduler cfq registered (default)
[    1.875000] pcieport 0000:00:09.0: Signaling PME through PCIe PME interrupt
[    1.882812] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[    1.890625] pci 0000:01:00.1: Signaling PME through PCIe PME interrupt
[    1.894531] pci 0000:01:00.2: Signaling PME through PCIe PME interrupt
[    1.902343] pci 0000:01:00.3: Signaling PME through PCIe PME interrupt
[    1.910156] pcieport 0000:00:11.0: Signaling PME through PCIe PME interrupt
[    1.914062] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
[    1.921875] pci 0000:02:00.1: Signaling PME through PCIe PME interrupt
[    1.929687] pci 0000:02:00.2: Signaling PME through PCIe PME interrupt
[    1.933593] pci 0000:02:00.3: Signaling PME through PCIe PME interrupt
[    1.945312] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    1.972656] serial8250.0: ttyS0 at MMIO 0x1fe001e0 (irq = 58) is a 16550A
[    1.976562] console [ttyS0] enabled, bootconsole disabled
[    1.976562] console [ttyS0] enabled, bootconsole disabled
[    1.992187] brd: module loaded
[    1.996093] loop: module loaded
[    2.000000] Loading iSCSI transport class v2.0-870.
[    2.003906] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
[    2.011718] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
[    2.019531] megasas: 06.811.02.00-rh1
[    2.023437] ahci 0000:00:08.0: SSS flag set, parallel bus scan disabled
[    2.031250] ahci 0000:00:08.0: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
[    2.039062] ahci 0000:00:08.0: flags: 64bit ncq sntf stag pm led clo only pmp pio slum part ccc apst
[    2.046875] scsi host0: ahci
[    2.050781] ata1: SATA max UDMA/133 abar m8192@0x49290000 port 0x49290100 irq 80
[    2.058593] ahci 0000:00:08.1: SSS flag set, parallel bus scan disabled
[    2.066406] ahci 0000:00:08.1: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
[    2.074218] ahci 0000:00:08.1: flags: 64bit ncq sntf stag pm led clo only pmp pio slum part ccc apst
[    2.082031] scsi host1: ahci
[    2.085937] ata2: SATA max UDMA/133 abar m8192@0x49292000 port 0x49292100 irq 81
[    2.093750] ahci 0000:00:08.2: SSS flag set, parallel bus scan disabled
[    2.101562] ahci 0000:00:08.2: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
[    2.109375] ahci 0000:00:08.2: flags: 64bit ncq sntf stag pm led clo only pmp pio slum part ccc apst
[    2.117187] scsi host2: ahci
[    2.121093] ata3: SATA max UDMA/133 abar m8192@0x49294000 port 0x49294100 irq 82
[    2.128906] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[    2.136718] e100: Copyright(c) 1999-2006 Intel Corporation
[    2.140625] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[    2.148437] e1000: Copyright (c) 1999-2006 Intel Corporation.
[    2.156250] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    2.160156] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    2.167968] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k
[    2.171875] igb: Copyright (c) 2007-2014 Intel Corporation.
[    2.234375] igb 0000:01:00.0: added PHC on eth0
[    2.242187] igb 0000:01:00.0: Intel(R) Gigabit Ethernet Network Connection
[    2.246093] igb 0000:01:00.0: eth0: (PCIe:5.0Gb/s:Width x4) dc:2d:cb:16:e6:c8
[    2.253906] igb 0000:01:00.0: eth0: PBA No: 106300-000
[    2.261718] igb 0000:01:00.0: Using MSI interrupts. 1 rx queue(s), 1 tx queue(s)
[    2.324218] igb 0000:01:00.1: added PHC on eth1
[    2.328125] igb 0000:01:00.1: Intel(R) Gigabit Ethernet Network Connection
[    2.335937] igb 0000:01:00.1: eth1: (PCIe:5.0Gb/s:Width x4) dc:2d:cb:16:e6:c9
[    2.343750] igb 0000:01:00.1: eth1: PBA No: 106300-000
[    2.347656] igb 0000:01:00.1: Using MSI interrupts. 1 rx queue(s), 1 tx queue(s)
[    2.378906] ata1: SATA link down (SStatus 0 SControl 300)
[    2.410156] igb 0000:01:00.2: added PHC on eth2
[    2.417968] igb 0000:01:00.2: Intel(R) Gigabit Ethernet Network Connection
[    2.421875] igb 0000:01:00.2: eth2: (PCIe:5.0Gb/s:Width x4) dc:2d:cb:16:e6:ca
[    2.429687] igb 0000:01:00.2: eth2: PBA No: 106300-000
[    2.437500] igb 0000:01:00.2: Using MSI interrupts. 1 rx queue(s), 1 tx queue(s)
[    2.453125] ata3: SATA link down (SStatus 0 SControl 300)
[    2.500000] igb 0000:01:00.3: added PHC on eth3
[    2.503906] igb 0000:01:00.3: Intel(R) Gigabit Ethernet Network Connection
[    2.511718] igb 0000:01:00.3: eth3: (PCIe:5.0Gb/s:Width x4) dc:2d:cb:16:e6:cb
[    2.519531] igb 0000:01:00.3: eth3: PBA No: 106300-000
[    2.523437] igb 0000:01:00.3: Using MSI interrupts. 1 rx queue(s), 1 tx queue(s)
[    2.585937] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    2.589843] ata2.00: ATA-9: FORESEE S50AF512GB, H190117H, max UDMA/133
[    2.597656] ata2.00: 1000215216 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    2.605468] ata2.00: configured for UDMA/133
[    2.609375] scsi 1:0:0:0: Direct-Access     ATA      FORESEE S50AF512 117H PQ: 0 ANSI: 5
[    2.656250] sd 1:0:0:0: [sda] 1000215216 512-byte logical blocks: (512 GB/476 GiB)
[    2.656250] sd 1:0:0:0: Attached scsi generic sg0 type 0
[    2.667968] sd 1:0:0:0: [sda] Write Protect is off
[    2.671875] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.683593]  sda: sda1 sda2 sda3
[    2.687500] sd 1:0:0:0: [sda] Attached SCSI disk
[    2.886718] igb 0000:02:00.0: added PHC on eth4
[    2.890625] igb 0000:02:00.0: Intel(R) Gigabit Ethernet Network Connection
[    2.898437] igb 0000:02:00.0: eth4: (PCIe:5.0Gb/s:Width x4) dc:2d:cb:16:e6:cc
[    2.906250] igb 0000:02:00.0: eth4: PBA No: 106300-000
[    2.910156] igb 0000:02:00.0: Using MSI interrupts. 1 rx queue(s), 1 tx queue(s)
[    3.273437] igb 0000:02:00.1: added PHC on eth5
[    3.277343] igb 0000:02:00.1: Intel(R) Gigabit Ethernet Network Connection
[    3.285156] igb 0000:02:00.1: eth5: (PCIe:5.0Gb/s:Width x4) dc:2d:cb:16:e6:cd
[    3.292968] igb 0000:02:00.1: eth5: PBA No: 106300-000
[    3.296875] igb 0000:02:00.1: Using MSI interrupts. 1 rx queue(s), 1 tx queue(s)
[    3.660156] igb 0000:02:00.2: added PHC on eth6
[    3.664062] igb 0000:02:00.2: Intel(R) Gigabit Ethernet Network Connection
[    3.671875] igb 0000:02:00.2: eth6: (PCIe:5.0Gb/s:Width x4) dc:2d:cb:16:e6:ce
[    3.675781] igb 0000:02:00.2: eth6: PBA No: 106300-000
[    3.683593] igb 0000:02:00.2: Using MSI interrupts. 1 rx queue(s), 1 tx queue(s)
[    4.046875] igb 0000:02:00.3: added PHC on eth7
[    4.050781] igb 0000:02:00.3: Intel(R) Gigabit Ethernet Network Connection
[    4.058593] igb 0000:02:00.3: eth7: (PCIe:5.0Gb/s:Width x4) dc:2d:cb:16:e6:cf
[    4.066406] igb 0000:02:00.3: eth7: PBA No: 106300-000
[    4.070312] igb 0000:02:00.3: Using MSI interrupts. 1 rx queue(s), 1 tx queue(s)
[    4.078125] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.0.2-k
[    4.085937] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[    4.089843] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 4.4.0-k-rh7.3
[    4.097656] ixgbe: Copyright (c) 1999-2016 Intel Corporation.
[    4.105468] ixgb: Intel(R) PRO/10GbE Network Driver - version 1.0.135-k2-NAPI
[    4.113281] ixgb: Copyright (c) 1999-2008 Intel Corporation.
[    4.117187] stmmac - user ID: 0xd1, Synopsys ID: 0x37
[    4.125000]  Enhanced/Alternate descriptors
[    4.128906]  Ring mode enabled
[    4.132812]  DMA HW capability register supported
[    4.136718]  RX Checksum Offload Engine supported (type 2)
[    4.140625]  TX Checksum insertion supported
[    4.144531]  Wake-Up On Lan supported
[    4.148437]  Enable GMAC 64bit DMA
[    4.152343]  Enable RX Mitigation via HW Watchdog Timer
[    4.156250] eth%d: device MAC address dc:2d:cb:16:e6:c6
[    4.167968] libphy: stmmac: probed
[    4.167968] eth8: PHY ID 01410dd1 at 1 IRQ 0 (stmmac-1:01) active
[    4.175781] stmmac - user ID: 0xd1, Synopsys ID: 0x37
[    4.179687]  Enhanced/Alternate descriptors
[    4.183593]  Ring mode enabled
[    4.187500]  DMA HW capability register supported
[    4.191406]  RX Checksum Offload Engine supported (type 2)
[    4.199218]  TX Checksum insertion supported
[    4.203125]  Wake-Up On Lan supported
[    4.207031]  Enable GMAC 64bit DMA
[    4.210937]  Enable RX Mitigation via HW Watchdog Timer
[    4.214843] eth%d: device MAC address dc:2d:cb:16:e6:c7
[    4.222656] libphy: stmmac: probed
[    4.226562] eth9: PHY ID 01410dd1 at 0 IRQ 0 (stmmac-2:00) active
[    4.234375] PPP generic driver version 2.4.2
[    4.238281] PPP BSD Compression module registered
[    4.242187] PPP Deflate Compression module registered
[    4.246093] PPP MPPE Compression module registered
[    4.253906] NET: Registered protocol family 24
[    4.257812] usbcore: registered new interface driver cdc_ether
[    4.261718] usbcore: registered new interface driver cdc_eem
[    4.269531] usbcore: registered new interface driver rndis_host
[    4.273437] usbcore: registered new interface driver cdc_ncm
[    4.281250] usbcore: registered new interface driver huawei_cdc_ncm
[    4.285156] usbcore: registered new interface driver cdc_mbim
[    4.292968] Generic UIO driver for PCI 2.3 devices version: 0.01.0
[    4.300781] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.304687] ehci-pci: EHCI PCI platform driver
[    4.308593] ehci-pci 0000:00:04.1: EHCI Host Controller
[    4.316406] ehci-pci 0000:00:04.1: new USB bus registered, assigned bus number 1
[    4.324218] ehci-pci 0000:00:04.1: irq 112, io mem 0x49278000
[    4.339843] ehci-pci 0000:00:04.1: USB 0.0 started, EHCI 1.00
[    4.343750] hub 1-0:1.0: USB hub found
[    4.347656] hub 1-0:1.0: 3 ports detected
[    4.351562] ehci-pci 0000:00:05.1: EHCI Host Controller
[    4.359375] ehci-pci 0000:00:05.1: new USB bus registered, assigned bus number 2
[    4.367187] ehci-pci 0000:00:05.1: irq 114, io mem 0x49288000
[    4.382812] ehci-pci 0000:00:05.1: USB 0.0 started, EHCI 1.00
[    4.386718] hub 2-0:1.0: USB hub found
[    4.390625] hub 2-0:1.0: 3 ports detected
[    4.394531] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.402343] ohci-pci: OHCI PCI platform driver
[    4.406250] ohci-pci 0000:00:04.0: OHCI PCI host controller
[    4.410156] ohci-pci 0000:00:04.0: new USB bus registered, assigned bus number 3
[    4.417968] ohci-pci 0000:00:04.0: irq 113, io mem 0x49270000
[    4.484375] hub 3-0:1.0: USB hub found
[    4.488281] hub 3-0:1.0: 3 ports detected
[    4.492187] ohci-pci 0000:00:05.0: OHCI PCI host controller
[    4.496093] ohci-pci 0000:00:05.0: new USB bus registered, assigned bus number 4
[    4.503906] ohci-pci 0000:00:05.0: irq 115, io mem 0x49280000
[    4.570312] hub 4-0:1.0: USB hub found
[    4.574218] hub 4-0:1.0: 3 ports detected
[    4.578125] uhci_hcd: USB Universal Host Controller Interface driver
[    4.582031] usbcore: registered new interface driver cdc_acm
[    4.589843] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    4.597656] usbcore: registered new interface driver cdc_wdm
[    4.601562] usbcore: registered new interface driver usb-storage
[    4.609375] usbcore: registered new interface driver usbserial
[    4.617187] usbcore: registered new interface driver option
[    4.621093] usbserial: USB Serial support registered for GSM modem (1-port)
[    4.628906] i8042: No controller found
[    4.632812] ls-rtc 100d0100.rtc: rtc core: registered 100d0100.rtc as rtc0
[    4.640625] i2c /dev entries driver
[    4.851562] cpufreq: Loongson-3 CPU frequency driver.
[    4.855468] usbcore: registered new interface driver usbhid
[    4.863281] usbhid: USB HID core driver
[    4.867187] Loongson Hwmon Enter...
[    4.871093] input: ACPI Power Button as /devices/virtual/input/input0
[    4.878906] ACPI Power Button Driver: Init successful!
[    4.882812] Netfilter messages via NETLINK v0.30.
[    4.886718] nfnl_acct: registering with nfnetlink.
[    4.890625] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[    4.898437] ctnetlink v0.93: registering with nfnetlink.
[    4.902343] IPVS: Registered protocols ()
[    4.906250] IPVS: Connection hash table configured (size=4096, memory=64Kbytes)
[    4.914062] IPVS: Creating netns size=1296 id=0
[    4.921875] IPVS: ipvs loaded.
[    4.921875] ip_tables: (C) 2000-2006 Netfilter Core Team
[    4.929687] TCP: cubic registered
[    4.933593] Initializing XFRM netlink socket
[    4.937500] NET: Registered protocol family 10
[    4.941406] mip6: Mobile IPv6
[    4.945312] NET: Registered protocol family 17
[    4.949218] NET: Registered protocol family 15
[    4.953125] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    4.968750] tipc: Activated (version 2.0.0)
[    4.972656] NET: Registered protocol family 30
[    4.976562] tipc: Started in single node mode
[    4.980468] registered taskstats version 1
[    4.984375] ls-rtc 100d0100.rtc: setting system clock to 2025-05-09 02:34:16 UTC (1746758056)
[    5.003906] Freeing unused kernel memory: 20484K (ffffffff80b0f000 - ffffffff81f10000)
/sbin/rc starting
Mounting file systems
Setting up loopback
node 0 total mem: 4096MB control plane mem: 1024MB
mnt part /dev/sda2, disk part /dev/sda3
/dev/sda2 was not cleanly unmounted, check forced.
/dev/sda2: 403/122160 files (7.4% non-contiguous), 75268/488281 blocks
mgt0 MAC address is : dc:2d:cb:16:e6:c6
mgt1 MAC address is : dc:2d:cb:16:e6:c7
ge2 MAC address is : dc:2d:cb:16:e6:c8
ge3 MAC address is : dc:2d:cb:16:e6:c9
ge4 MAC address is : dc:2d:cb:16:e6:ca
ge5 MAC address is : dc:2d:cb:16:e6:cb
ge6 MAC address is : dc:2d:cb:16:e6:cc
ge7 MAC address is : dc:2d:cb:16:e6:cd
ge8 MAC address is : dc:2d:cb:16:e6:ce
ge9 MAC address is : dc:2d:cb:16:e6:cf
init mp forwarding mp_fw0
init mp local mp_local0
init mp control mp_control0
Page size 16384 bytes, memory regions:
 0: 0xff3610c000 -> 0xff737a7e80 (1030340224 bytes)
 1: 0xff95004000 -> 0xfff3ffff80 (1593819008 bytes)
 2: 0xfff4204000 -> 0xfff42e6880 (927872 bytes)
 3: 0xfff4804000 -> 0xfff4ffff80 (8372096 bytes)
Memory reserved 16 MB for configuration
Buddy initialized
Slub initialized
nf_conntrack (size 512 buckets 2097152 max 2000000) memory:4GB
Application identify initialized
Application audit initialized
Intrusion Prevention System initialized
Anti-Virus Protection initialized
WAF initialized
% Unknown command: ftp timeout 5
.
% Unknown command: wxfj-place 64
.
ge4 add to group agg1!
ge5 add to group agg1!
% Unknown command: wxfj-upload-encryp enable
.
% Unknown command: wxfj-rzx-cszt disable
.
% Unknown command: wxfj-pass-switch disable
.
% Unknown command: ap ipmac enable
.
The configuration is loaded !
2025-05-09 10:35:55:mgt0 link change to UP !
2025-05-09 10:35:55:mgt1 link change to UP !
watchdog init ok.
watchdog pthread init ok.
2025-05-09 10:35:59:mgt0 link change to DOWN !
2025-05-09 10:35:59:mgt1 link change to DOWN !
/sbin/rc complete
Username:
Username: